The most important menu codes
for the weighing mode:
Amb. conditions Code
Very stable 1 1 1*
Stable 1 1 2*
Unstable 1 1 3
Very unstable 1 1 4
Weighing/filling Code
Std. weighing 1 2 1*
Filling 1 2 2
Stability Range
When the stability symbol/wt. unit
is displayed, the weight readout
is stable within the defined range.
Code
0.25 digit 1 3 1
0.5 digit 1 3 2*
1 digit*** 1 3 3
2 digits*** 1 3 4*
4 digits*** 1 3 5
8 digits** 1 3 6
Tare parameter Code
At any time** 1 5 1
After stability 1 5 2*
At stability 1 5 3
Auto Zero Code
On 1 6 1*
Off 1 6 2
Data Output
Automatic output
of parameters Code
Off 7 1 1*
Ref. %/qty. + ref. wt. 7 1 2
Ref. weight only 7 1 3
Data ID code Code
Without 7 2 1*
With 7 2 2
Auto tare output/print Code
Indiv. tare weight 7 3 1*
Tare weight total 7 3 2
Output parameter Code
Without stability 6 1 1
After stability 6 1 2*
At stability 6 1 3
Auto w/o stability 6 1 4
Auto after stability 6 1 5
Auto tare after output Code
Off 6 4 1*
On 6 4 2
Additional Functions
Access to menu Code
Accessible 8 1 1
Dep. on switch setting** 8 1 2*
Beep tone Code
On 8 2 1*
Off 8 2 2
***= factory setting; depends on the
balance model in some cases
***= does not apply to balance
models verified
for legal metrology
***= only does not apply to verified
AC balances
The Most Important Menu Code Settings
These charts summarizing the menu parameters for standard weighing have been compiled to provide you with
a quick-reference guide.
Weighing in Three Ranges Max.
One range Code 2 1 1
Two ranges Code 2 1 2*
Three ranges Code 2 1 3**
Weight units 1st range 2nd range 3rd range**
Grams (o)** 1 7 1 3 1 1 3 3 1
Grams 1 7 2* 3 1 2* 3 3 2*
Kilograms*** 1 7 3 3 1 3 3 3 3
Carats** 1 7 4 3 1 4 3 3 4
Pounds** 1 7 5 3 1 5 3 3 5
Ounces** 1 7 6 3 1 6 3 3 6
Troy ounces** 1 7 7 3 1 7 3 3 7
Hong Kong taels** 1 7 8 3 1 8 3 3 8
Singapore taels** 1 7 8 3 1 9 3 3 9
Taiwanese taels** 1 7 10 3 1 10 3 3 10
Grains** 1 7 11 3 1 11 3 3 11
Pennyweights** 1 7 12 3 1 12 3 3 12
Milligrams** 1 7 13 3 1 13 3 3 13
Application Programs
Program
Key Code
Counting F2 2 1 4
Weighing in percent F2 2 1 5
Tare memory/net total F1 2 2 2
Over/under checkweighing (net wt.) F1 2 2 3
Over/under checkweighing (diff.in wt.) F1 2 2 4
IQ-Mode for Standard Balances
In the IQ-Mode,** weighing is done with a
load-dependent readability. Select the load-dependent
display accuracy independently for each of the three
weighing ranges.
Code Code Code
1st range 2nd range 3rd range
1 % accuracy 1 8 6 3 2 6 3 4 6*
0.5 % accuracy 1 8 7 3 2 7 3 4 7
0.2 % accuracy 1 8 8 3 2 8 3 4 8
0.1 % accuracy 1 8 9 3 2 9* 3 4 9
0.05% accuracy 1 8 10 3 2 10 3 4 10
0.02% accuracy 1 8 11 3 2 11 3 4 11
0.01% accuracy 1 8 12 3 2 12 3 4 12
Display Modes
Code Code Code
1st range 2nd range 3rd range
Highest accuracy 1 8 1* 3 2 1* 3 4 1
Last num. blanked
when load changes 1 8 2 3 2 2 3 4 2
Rounding factor 2**1 8 3 3 2 3 3 4 3
Rounding factor 5**1 8 4 3 2 4 3 4 4
Rounding factor10**1 8 5 3 2 5 3 4 5
PolyRange** 1 8 13 3 2 13 3 4 13
***= factory setting; depends on the balance model
in some cases
***= does not apply to balance models verified
for legal metrology
***= blocked on verified AC balances
Calibration/Adjustment and
Linearization Functions
External cal. Code**
Accessible 1 9 1*
Access denied 1 9 2
Internal cal. Code**
Accessible 1 10 1*
Access denied 1 10 2
Sensitivity test*** Code
Accessible 1 11 1*
Access denied 1 11 2
Quick CAL using f Code
Quick CAL (“CAL I”) 2 2 5*
Quick sensitivity test*** 2 2 6
Application Program Functions
Ref. for % + counting Code
No change 2 3 1
5,10, 20, ... 2 3 2*
In increments of 1 2 3 3
Readout in percent Code
Without decimal 3 6 1
1 decimal 3 6 2*
2 decimals 3 6 3
3 decimals 3 6 4
Over/under
tolerance limits Code
+/– 0.1% deviation 4 1 1
+/– 0.2% deviation 4 1 2
+/– 0.5% deviation 4 1 3
+/– 1.0% deviation 4 1 4*
+/– 1.5% deviation 4 1 5
+/– 2.0% deviation 4 1 6
+/– 2.5% deviation 4 1 7
+/– 3.0% deviation 4 1 8
+/– 5.0% deviation 4 1 9
+/– 10.0% deviation 4 1 10
Auto output of
acceptable values Code
On 4 2 1
Off 4 2 2*
Interface
Baud rate Code
150 baud 5 1 1
300 baud 5 1 2
600 baud 5 1 3
1,200 baud 5 1 4*
2,400 baud 5 1 5
4,800 baud 5 1 6
9,600 baud 5 1 7
19,200 baud 5 1 8
Parity Code
Mark parity** 5 2 1
Space parity** 5 2 2
Odd parity 5 2 3*
Even partiy 5 2 4
Number of stop bits Code
1 stop bit 5 3 1*
2 stop bits 5 3 2
Handshake mode Code
Software 5 4 1
Hardware w/2
characters after CTS 5 4 2*
Hardware w/1
character after CTS 5 4 3
Reset Function
The reset function enables you to
reset all codes back to the factory
settings identified by an “*” in the
charts. Select code 9 – – 1
o
, confirm
by pressing t, then press c.
***= factory setting
***= does not apply to balance
models verifiable/verified for
legal metrology
***= does not apply to verified/
verifiable LC balances
To Previous Page
Loading...