Scaime eNod4-D ETHERNET - Stop cycle

81 pages

Save Page as PDF

To Next Page

To Previous Page

SCAIME Manual : NU-eNod4D-ETH-E-0418_216710-E.docx

 Else the cycle is suspended until a new request of starting the cycle is activated.

11.3.3 Stop cycle

This edge-active input causes the feeding cycle to be stopped inhibiting the different outputs involved.

Main Page

Table of Contents2
Safety Instructions5
Getting Started5
Protection6
Power Supply6
Grounding6
Installation6
Maintenance6
Caution6
Enod4 Product Range7
General Presentation7
Versions7
Communication Protocol Versions7
IO+ Version7
Bluetooth ® Version7
Enodview Software8
Enodapp - Mobile Application8
General Characteristics9
Dimensions9
Electrical Characteristics11
Legal for Trade12
Connections14
Cabling Basic Rules15
Prevent Electrostatic Discharges15
Prevent Electromagnetic Disturbances16
Power Supply Connection17
Load-Cell Wiring17
IO+ Version17
Inputs / Outputs Connections18
Typical Connections19
JB4 Option19
Specifications20
Excitation Trimming Procedure20
Spring Terminal Connections21
220V Option21
Communication22
Communication Interface Connections22
Process Control Communication22
PC Communication22
AUX Communication (for HMI)22
Communication Address Selection22
Communication Rate Selection23
Communication Protocols23
Simultaneous Functioning of Communications24
Bluetooth ® Communication (Optional)25
Calibration and Scale Adjustment26
Physical Calibration26
Theoretical Calibration26
Scale Adjustment Coefficient26
Gravity Correction26
Scale Interval26
Filters27
Filtering Related to the A/D Conversion Rate27
Bessel Low Pass Filter27
Notch Filter27
Self-Adaptive Filter27
Measurement and Status28
Gross Measurement28
Net Measurement28
Tare Value28
Factory Calibrated Points28
Logical IN/OUT Level28
Preset Tare Value28
Measurement Status28
Weighing Diagnosis28
Global Weighing Diagnosis28
Inputs Functioning29
Inputs Assignment29
General Functions29
Functions Attached to an Operating Mode29
Outputs Functioning30
Outputs Assignment30
General Functions30
Functions Attached to an Operating Mode31
Feeding Mode in Dosing Processes31
Analog Output (IO+ Version)31
Dosing by Filling Operating Mode33
Starting Conditions35
Cycle Description35
Flow Rate Control (Optional)35
Automatic Taring at Start35
Coarse Feed Effect Neutralization Time35
Fine Feed Level35
Fine Feed Effect Neutralization Time36
Target Weight and In-Flight Weight36
Final Stabilization Time36
Tolerances36
End of Emptying Level and Emptying Holding Time36
End of Cycle Waiting Time36
Effective End of Cycle36
Inputs Utilization36
Start Cycle36
Suspend Current Cycle36
Stop Cycle37
Dosing by Unloading Operating Mode38
Reloading Management39
Reloading at the End of the Cycle40
Reloading at the Start of the Cycle40
Cycle Description40
Flow Rate Control (Optional)40
Verification of the Available Product Quantity40
Start Delay40
Coarse Feed Effect Neutralization Time40
Fine Feed Level40
Fine Feed Effect Neutralization Time40
Target Weight and In-Flight Weight40
Final Stabilization Time41
Tolerances41
End of Cycle Waiting Time41
Effective End of the Cycle41
Digital Inputs Utilization41
Start Cycle41
Suspend Current Cycle41
Stop Cycle41
Enodtouch - Interface Homme Machine (Option)42
Online Functioning42
Startup Screens42
Multi-Enod Screens43
Main Screen47
Result Displaying and Storage (Enod4-C, Enod4-D)51
Main Setup Menu53
Dosing Setup Menu (Enod4-D)73
Dosing Cycle Setup74
Starting Conditions Setup75
Dosing Timing Setup76
In-Flight Correction Settings77
Flow Rate Control Settings78
Dosing Tolerance Control79
Dosing Target Values79
Configuration of Quick Access Menu81

Scaime eNod4-D ETHERNET - Stop cycle

Table of Contents

Related product manuals