Scanlab RTC 4 - Initialization and Configuration Commands; Advanced Programming and Control Flow; Status Monitoring and I;O Commands

RTC
®
4 PC Interface Board
Rev. 1.3 e
10 Commands And Functions
70
innovators for industry
Control Commands
Initialization And Field Correction
(n_) load_program_file .................................... 96
(n_) load_correction_file ................................. 95
(n_) select_cor_table ...................................... 102
(n_) load_varpolydelay .................................... 97
(n_) dsp_start ................................................... 80
Laser Mode And Parameters
(n_) set_laser_mode ...................................... 108
(n_) set_firstpulse_killer ................................ 105
(n_) set_softstart_level .................................. 114
(n_) set_softstart_mode ................................ 115
(n_) set_standby ............................................ 116
(Also see the corresponding list commands,
page 71.)
Scanner Delay Mode
(n_) set_delay_mode ..................................... 104
Coordinate Transformations
(n_) set_matrix ............................................... 110
(n_) set_offset ................................................ 111
Status Monitoring and Diagnostics
(n_) get_head_status ....................................... 82
(n_) get_value .................................................. 87
(n_) get_waveform .......................................... 88
(n_) measurement_status ............................... 99
intelliSCAN
®
Commands
(n_) control_command .................................... 77
I/O Commands
(n_) get_io_status ............................................ 84
(n_) read_io_port ............................................. 99
(n_) write_8bit_port ...................................... 122
(n_) write_da_x .............................................. 123
(n_) write_io_port .......................................... 123
(Also see the corresponding list commands,
page 71.)
External Control Inputs
(n_) set_control_mode .................................. 103
(n_) select_list ................................................ 102
(n_) set_max_counts ...................................... 110
(n_) get_counts ................................................ 81
(n_) get_startstop_info .................................... 85
List Handling And Status
(n_) set_start_list ........................................... 116
(n_) execute_list ............................................... 81
(n_) stop_execution ....................................... 119
(n_) stop_list .................................................. 119
(n_) restart_list ............................................... 101
(n_) get_status ................................................. 86
(n_) read_status ............................................. 100
Synchronization Of Processing
(n_) get_wait_status ........................................ 88
(n_) release_wait ............................................ 101
Automatic List Handling
(n_) auto_change ............................................. 75
(n_) auto_change_pos ..................................... 75
(n_) start_loop ............................................... 119
(n_) quit_loop .................................................. 99
Circular Queue Mode
(n_) set_list_mode ......................................... 109
(n_) get_list_space ........................................... 84
Structured Programming
(n_) set_input_pointer ................................... 106
(n_) get_input_pointer .................................... 83
(n_) execute_at_pointer .................................. 81
Direct Laser And Scan Head Control
(n_) disable_laser ............................................. 80
(n_) enable_laser .............................................. 80
(n_) laser_signal_on ......................................... 92
(n_) laser_signal_off ........................................ 91
(n_) goto_xy ..................................................... 89
(n_) get_xy_pos ................................................ 88
(n_) z_out ....................................................... 124
Scanning Raster Images (Bitmaps)
n_) read_pixel_ad ......................................... 100
(Also see the corresponding list commands, page 71)
Using Multiple RTC
®
4 Boards In One
Computer
rtc4_count_cards .................................... 101
select_rtc ................................................. 103