To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...Why does my Scheppach BASA1 Saw motor overheat easily?
If your Scheppach Saw motor overheats easily, it's likely due to overloading or insufficient cooling. Avoid overloading the motor while cutting. Also, remove dust from the motor to ensure optimal cooling.
What to do if Scheppach Saw blade jams during cutting work?
If the Scheppach Saw blade jams during cutting work, it could be due to a blunt saw blade, deposits on the saw blade, or a poorly set guide. Try changing the saw blade, cleaning the saw blade, and setting the saw blade guide according to the operating instructions.
Why do burn marks appear on the wood during cutting with Scheppach BASA1?
If burn marks appear on the wood during cutting with your Scheppach Saw, it's likely due to a blunt or wrong saw blade. Change the saw blade and select a suitable one according to the operating instructions.
How to fix a rough or wavy saw cut with Scheppach Saw?
If your Scheppach Saw cut is rough or wavy, the saw blade may be dull, or the tooth shape may not be appropriate for the material thickness. Resharpen the saw blade and/or use a suitable saw blade.
What to do if workpiece pulls away and/or splinters with Scheppach Saw?
If the workpiece pulls away and/or splinters when using your Scheppach Saw, it's likely due to excessive cutting pressure or an unsuitable blade. Insert a suitable saw blade.
Why is Scheppach Saw blade not running straight?
If your Scheppach Saw blade is not running straight, the guide may have been wrongly set, or you may be using the wrong saw blade. Set the saw blade guide according to the operating instructions and select a saw blade according to the operating instructions.
Why doesn't my Scheppach BASA1 Saw motor reach its full power?
If the Scheppach Saw motor does not reach its full power, it may be because the circuits in the network are overloaded. Avoid using any other equipment or motors on the same circuit.
How to troubleshoot a Scheppach BASA1 when the motor does not work?
If the Scheppach Saw motor does not work, the motor, cable, or plug could be defective, or the housing cover might be open. Arrange for a specialist to inspect the machine and never attempt to repair the motor yourself due to the danger. Check the fuses and replace them if necessary. Ensure the housing cover is closed exactly.
Why does Scheppach BASA1 Saw motor start slowly?
If the Scheppach Saw motor starts up slowly and does not reach operating speed, the voltage may be too low, the coils may be damaged, or the capacitor may be faulty. Contact the utility provider to check the voltage. Arrange for a specialist to inspect the motor and replace the capacitor.
What causes a Scheppach BASA1 Saw motor to make excessive noise?
If the Scheppach Saw motor makes excessive noise, the coils may be damaged, or the motor may be defective. Arrange for inspection of the motor by a specialist.
General| Input power | 300 W |
|---|---|
| Power source | AC |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Idle speed (max) | - RPM |
| Cutting depth (90º) | 100 mm |
| Cutting width (90°) | 195 mm |
| Sliding rails | - |
Weight and Dimensions| Depth | 395 mm |
|---|---|
| Width | 440 mm |
| Height | 710 mm |
Details noise levels and advises on the use of hearing protection during operation.
Step-by-step guide for attaching the saw table to the machine frame.
Instructions on how to correctly tension the bandsaw blade for safe operation.
Procedure for aligning the saw band on the rollers for optimal cutting.
Guidance on adjusting top and bottom support bearings and guide rollers.
Instructions for setting the saw table to a precise 90-degree angle.
Procedure for safely removing and installing a new bandsaw blade.
How to use the main power switch to turn the machine on and off.
Instructions for setting and using the parallel stop for straight cuts.
Technique for cutting wood along its length using the parallel fence.
Guidance on making angled cuts, including use of the parallel stop.
Techniques for cutting curves and radii freehand with the bandsaw.
