SCS LABCOTER 2 - Page 7

OM-610-1002-1 Operator’s Manual Rev 37
6.2.5 Feed-Thru Rebuild........................................................................................................................ 40
6.3 PROCESS TEMPERATURE CONTROLLERS.......................................................................... 41
6.3.1 Verifying the WEST Model 6100+ Temperature Controller......................................................... 42
6.3.2 Vacuum Controller........................................................................................................................42
6.3.3 Calibrating the Granville-Phillips Zero Pressure Simulator........................................................ 43
6.3.4 Verifying the WEST Model 6100+ Vacuum Process Controller................................................... 43
6.3.5 Vacuum Amplifier Circuit Board Calibration............................................................................... 44
6.4 PROCESS CONTROLLER PARAMETERS ..............................................................................45
6.4.1 To Enter the Configuration Mode:................................................................................................ 45
6.4.2 To Exit the Configuration Mode:.................................................................................................. 45
6.4.3 To Enter the Setup Mode: ............................................................................................................. 46
6.4.4 To exit the Setup Mode: ................................................................................................................ 46
6.4.5 Factory Settings ............................................................................................................................ 47
6.4.6 Detailed Description of Parameters ............................................................................................. 51
6.5 OPERATION AND MAINTENANCE LOGS.............................................................................55
6.6 SUPPLIES FOR SERVICING .....................................................................................................56
6.7 COATING PROBLEMS AND SOLUTIONS.............................................................................. 56
SECTION 7 COMPONENT LOCATION & PART NUMBERS ....................................................59
7.1 COMPONENT LOCATION-STANDARD MACHINE.................................................................... 59
7.2 COMPONENT LOCATION-OPTIONS ........................................................................................ 59
FD-610-1007-1 FACILITIES DRAWING................................................................................................61
AD-610-1010-1 120V ASSEMBLY .........................................................................................................63
AD-610-1011-1 220V ASSEMBLY .........................................................................................................65
AD-610-1065-1 200 VOLT ASSEMBLY.................................................................................................67
AD-286-1041-1 BASIC FRAME ASSEMBLY 1 OF 2 ............................................................................69
AD-286-1041-1 BASIC FRAME ASSEMBLY 2 OF 2.............................................................................. 71
AD-610-1001-4 ELECTRICAL PANEL ASSEMBLY ............................................................................ 73
AD-215-1007-1 LOAD DOOR ASSEMBLY...........................................................................................75
AD-374-1029-2 HEATER ASSEMBLY ..................................................................................................77
AD-241-1007-1 FIXTURE ROTATION ASSEMBLY ............................................................................ 79
AD-157-1019-1 LN2 CHILLER ASSEMBLY 1 OF 2..............................................................................81
AD-157-1019-1 LN2 CHILLER ASSEMBLY 2 OF 2..............................................................................83
AD-724-1097-1 LN2 LEVEL CONTROLLER ASSEMBLY .................................................................. 85
AD-241-1008-1 STANDARD FIXTURE................................................................................................. 87
D50016 VACUUM CHAMBER............................................................................................................... 89
AD-088-1031-1 CHAMBER WITH VIEWPORT & LID.........................................................................91
FP-088-1081-1 REDUCED DOME CHAMBER......................................................................................93
AD-285-1161-1 TUMBLE KIT 1 OF 3....................................................................................................95
AD-285-1161-1 TUMBLE KIT 1 OF 3....................................................................................................95
AD-285-1161-1 TUMBLE KIT 2 OF 3 ...................................................................................................... 97
AD-285-1161-1 TUMBLE KIT 3 OF 3 ...................................................................................................... 99
AD-285-1055-1 TUMBLE ADAPTOR 1 OF 2 ........................................................................................101
AD-285-1055-1 TUMBLE ADAPTOR 2 OF 2 ........................................................................................103
AD-241-1185-1 FIXTURE 3”.................................................................................................................... 105
AD-684-1005-1 TUMBLER BASKET (OPTION)................................................................................. 107
SECTION 8 SPARE PARTS ............................................................................................................. 109
8.1 SPARE PARTS KITS.................................................................................................................109
SA-285-1028-3 BASIC SPARE PARTS KIT........................................................................................... 109
SA-285-1033-2 COMPREHENSIVE SPARE PARTS KIT .....................................................................110