Sharp AR-5726 - Photo Mode

AR-5726/5731 SIMULATION 6 - 29
Operation/procedure
1. Touch the item to be adjusted.
The currently set value is highlighted beside the adjustment item.
2. Press the [START] key.
The display is shifted to the adjustment value entry menu.
3.
Enter the adjustment value with the 10-key, and press the [START] key.
When the [SYSTEM SETTINGS] key is pressed, the display returns to
the original state (adjustment item selection menu).
* Auto exposure mode
• When SIM 26-6 (Destination setup) is changed from EX Japan to
Japan, the setup value becomes 1 (Default: Japan). If, on the con-
trary, it is changed from Japan to EX Japan, the set value becomes
2 (Default: EX Japan)
• If the auto exposure mode setup value is changed, the setup value
of SIM 46-30 (AE limit setup) is reset to the default value.
Operation/procedure
1. Touch the item to be adjusted.
The adjustment item and the currently set value are highlighted.
2. Enter the set value with the 10-key.
Operation/procedure
1. Touch the item to be adjusted.
The adjustment item and the currently set value are highlighted.
2. Enter the set value with the 10-key.
If SIM 26-6 (Destination setup) and SIM46-19 (Auto exposure mode)
are changed, this setup is also changed to the default value accord-
ingly.
Operation/procedure
1. Touch the item to be adjusted.
The adjustment item and the currently set value are highlighted.
2. Enter the set value with the 10-key.
Enter the set value with the 10-key.
Operation/procedure
1. Touch the item to be set.
The item and the currently set value are highlighted.
2. Press the [START] key.
The display is shifted to the copy menu.
3. Select the paper feed tray and the print density, and enter the
adjustment value with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
46-19
Purpose Adjustment
Function
(Purpose)
Used to set the control method of the exposure mode.
Item Picture quality
Item Content Default
1
AE MODE
(1:EXPOSURE
2:TONER)
Auto exposure mode*
(1: Priority on Image quality,
2: Priority on toner consumption)
2
2
AE STOP(COPY)
(0:FIXED
1:REAL TIME)
Auto exposure STOP mode
(COPY)
(0: Fixed, 1: Real-time)
0
3
AE MODE(FAX)
(0:FIXED
1:REAL TIME)
Auto exposure STOP mode (FAX)
(0: Fixed, 1: Real-time)
0
4
AE STOP(SCAN)
(0:FIXED
1:REAL TIME)
Auto exposure STOP mode
(SCANNER)
(0: Fixed, 1: Real-time)
0
5
PHOTO MODE
Photo mode
(1: ED (Error diffusion) , 2: DT (Dither))
2
46-20
Purpose Adjustment
Function
(Purpose)
Used to set the exposure correction value of SPF/
RSPF for OC exposure.
Item Picture quality
Item Content Setting range Default
1
SPF EXPOSURE SPF
1-99 53
2
RSPF EXPOSURE RSPF
46-30
Purpose Setting
Function
(Purpose)
Used to set the AE and the limit value in AE
(Toner save).
Item Setting range Default
1AE
0-31 0
2 AE(TS)
46-31
Purpose Setting
Function
(Purpose)
Used to set the AE and the limit value in AE
(Toner save).
Item Setting range Default
1AE
0-2 1
2 TEXT
3 TEXT/PHOTO
4PHOTO
46-39
Purpose Setting
Function
(Purpose)
Used to switch the FAX send image quality.
Item Content Setting range Default
0HAIRLINE
Original with pencil lines
and thin lines
0-1 0
1 PRINTER Printed original
48
48-1
Purpose Adjustment
Function
(Purpose)
Used to adjust the copy mode magnification ratio
(main scanning direction, sub scanning direction).
Section Image processing
Item Picture quality
Item Content
Setting
range
Default
1F-R
Main scanning magnification
ratio adjustment
1-99
50
2SCAN
Sub scanning magnification
ratio adjustment
60
3 SPF (SIDE1)
RSPF surface sub scan
magnification ratio
50
4 SPF (SIDE2)
RSPF back surface sub scan
magnification ratio
5 DUPLEX
DUPLEX sub scanning
magnification ratio adjustment
6 MirSpeed Mirror speed adjustment