I-1
Appendix I
Application Specific Detection (ASD)
allows the system designer (and anyone
with Control menu access) to program an
ILP-2 detector’s sensitivity, pre-alarm
threshold, and other alarm-related param-
eters using English descriptions of the
detector's environment (application). This
eliminates the need for detailed knowledge
of smoke detector terminology and
operation. The designer can set all of the
critical detector parameters by simply
selecting an application description that
closely fits the one where the detector is to
be installed.
For example, to use ASD to select the
optimal parameters for a detector in a hotel
lobby, select the LOBBY application in the
CSG-M for that device. The MXL will
automatically transmit the factory deter-
mined sensitivity, pre-alarm threshold, and
detection algorithm (R-algorithm) to the
corresponding device. This eliminates the
guesswork of selecting these parameters
for different environments. Changes made
at the control panel using the Control menu
(Change_Apps) override the ASD settings
made in CSG-M for that ILP-2 device until
the next power-on reset.
Application Specific Detection
(ASD)
SNOITAIVERBBAUNEMBUSDSA
LXM
uneM
noitacilppAM-GSCnoitpircseD
ENON
elbasiD
cirtceleotohPdradnatS(snoitacilppAoN
)rotceteD
CFFO
)liateR(eciffO
dellortnocetamilc,naelcylbanosaeR
erehpsomta
ESHW
thgiL(esuoheraW
)gnirutcafunaM
dnakcurtkrof,tnempiuqe,tsudenrobriA
semuftsuahxeaerakcodmuidemotthgil
YBOL
ybboL
,segnahcerutarepmet,aeranaelcylevitaleR
gnikoms,senohpralullec
PMOC
mooRretupmoC
,naelc,tnemnorivnedellortnocyreV
tsochgih,detalugerylesolcerutarepmet
hgih,gnikomson,gnitar
epoyrenihcamnaelc
yticolevria
MROD
yrotimroD
,segnahcerutarepmetdnatsudenrobriA
gnikoms,semufgnikooc,sretrauqgnivil
HTLH
erachtlaeH
cinortcele,naelcylevitaler,ksirlevelrehgiH
tnempiuqe
KRAP
egaraGgnikraP
,semufleseiddnarac,tsudenrobriA
sgniwserutarepmet
LITU
)remrofsnarT(ytilitU
mooR
taeh,tnemnorivneytridtahwemosotlamroN
tnempiuqegninnurmorf
CERP
egarotSsuoicerP
evitisneS(
)tnemnorivnE
,egarotstnempiuqeroslairetamevitisneS
tseilrae,tnemnorivneeerf-ts
udnaelc
derisedgninraw
TSOH
tnemnorivnEelitsoH
FR,tnempiuqegnitarepo,dimuh,ytsud,ytriD
sgniwserutarepmetediw,tneserp
TCUD
rorianepO(tcuD
)gnisuohtcud
erutarepmetediw,dimuh,ytsud,ytriD
yticolevriahgih,sgniws
NOTES:
1. The ILP-2 is only compatible with MXL-IQ Revision 3.0 or
greater firmware.
2. The FP-11/FPT-11 is only compatible with MXL-IQ Revision
6.0 or greater firmware.
3. When the CSG-M is configured, the DUCT application
must be selected when the device is used in an air duct
housing or in a spot duct application.
To Next Page
Loading...
