Siemens MXL-IQ - Overview of the Menus Structure

3-15
Operation
Overview of the Menu’s Structure
Press ENTER to enter the menu. The
menu then uses the first 32 spaces of the
second line of the display to communicate
with you. When you use the Acknowledge
or List menu, the menu uses both lines of the
display.
If you are in the menu and do not depress a
numeric or arrow key at any time during a 1
minute period, the System returns to the
previous item.
The five Main Menu items and their subitems
for Revision 6.0 and higher follow; the
shortened terms used in the menu itself are
in parentheses:
81ELBAT
DAPYEKDNAMMOC
yeKesopruP
|
gnihsalfsitahwfotfelehtotmetiehttceleS
.)rebmunagniretnesselnu(yalpsidehtno
}
sitahwfothgirehtotmetiehttceleS
agniretnesselnu(yalpsidehtnognihsalf
.)rebmun
~
.metisuoiverpehtotkcaboG
RETNE
rosrucehthcihwnometiehttcelesotsserP
sserp,srebmunnignipytretfA.gnihsalfsi
.yrtneehtetelpmocotRETNE
PLEH
.egassemenil-enoayalpsidotsserP
TNIRP
dnastsilsuoiravgnitnirpnigebotsserP
.stroper
MROF
DEEF
.retnirpehtnirepapehtecnavdaotsserP
RAELC
gnisserpybnugebstuotnirplecnacotsserP
:tnirplliwmetsySehT.TNIRP
detanimretylerutamerpgnitsilsihT .
Acknowledge
Alarm
Supervisory (Supervsry)
Security
Trouble
List
1
Status
Alarm
Supervisory (Supervsry)
Security
Trouble
Sensitivity (Senstvty)
Voltages
- Analog
- Threshold
- Sensitivity
Temp
Module type (Mod type)
Device type (Dev type)
Message
Software version
(SW version)
Output States
Device Usages
Node Address
Air Sampling
- Smoke-lev
- Flow-lev
- Trip-pts
Percent/ft
- Senstvty
- Pre-alarm
- Analog
ASD apps
1
You can generate a
printed report or listing
for every item in the List
menu except Node
Address; see the
discussion under LIST
Menu.
Control
Reset
Sensitivity (Senstvty)
- Hi_3
- Hi_2
- Hi_1
- Norm
- Low_1
- Low_2
- Low_3
Arm/disarm (Arm/dis)
- Arm
- Disarm
Output on/off
- Arm
- Disarm
- Energize
- De-Energize
Loop Arm
Loop Disarm
Netlink Request
Air Sampling
- Alarm_Trip
- Flow_Trip
Percent/Ft
- Sensitivity
(Senstvty)
- Pre_alarm
Change_Apps
Test
Set time
Ground fault (Gnd_flt)
- Main
Power
2
- Main
- Voltage
- Current
Lamp test
- LEDs
- Display
Device LED
MOI_Lamp_Test
X-Network
M-Network
Override
Det_cleaned
Event_log
- Alrm_only
- Superv_only
- Security_only
- Trbl_only
- All_events
- Hist_Ctrl
- Hist_Erase
Pyro_diags
Pre_alarm
ASD_Devices
Summarize
Manual_Activate
2
You can generate a
printed report for this
item; see the discussion
under TEST Menu.
Walktest
System_wAUD
Loop_wAUD
Zone_wAUD
System_SIL
Loop_SIL
Zone_SIL
Cancel
Extend