Need help?Do you have a question about the Siemens SIMATIC ET 200PA SMART and is the answer not in the manual?
General| Product type designation | ET 200PA SMART |
|---|---|
| Bus System | PROFIBUS PA |
| Supply voltage | 24 V DC |
| Input Voltage | 24 V DC |
| Protection Class | IP20 |
| Series | SIMATIC |
| Subseries | SMART |
| Communication Interface | PROFIBUS PA |
| Relative Humidity | 5% to 95% (non-condensing) |
| Connection Method | Screw-type terminal |
| Dimensions | Varies depending on specific module type within the ET 200PA SMART series. Consult specific module documentation for exact dimensions. |
Explains the scope and goal of the operating instructions for the ET 200PA SMART system.
Outlines the prerequisite general experience needed to understand the manual.
Specifies the product versions and modules covered by these operating instructions.
Describes the ET 200PA SMART manual's place within the overall Siemens documentation.
Refers to section "Standards and approvals" for relevant certifications.
Information on access aids like table of contents and index for quick information retrieval.
Instructions on how to request technical support for Industry Automation products.
Details on accessing online documentation, newsletters, and forums for product support.
Information on finding personal Siemens representatives for further assistance.
Guidance on implementing industrial security concepts and product update recommendations.
Explanation of distributed I/O devices and their application in automation systems.
Definition and physical characteristics of the PROFIBUS DP bus system.
Definition and technical setup of the ET 200PA SMART Distributed I/O device.
Overview of components and their functions for configuring the ET 200PA SMART system.
Detailed listing of essential components for ET 200PA SMART configuration and commissioning.
Explains limit conditions and module compatibility for ET 200PA SMART configurations.
Details on mounting dimensions, clearances, and rail lengths for ET 200PA SMART.
Rules and guidelines for arranging modules for dynamic replacement and redundant operation.
General rules and regulations for safe electrical integration of the ET 200PA SMART.
Information on configuring ET 200PA SMART with grounded supply (TN-S system).
Details on configuring ET 200PA SMART with ungrounded reference potential for specific applications.
Explanation of using electrically isolated modules in the ET 200PA SMART configuration.
Introduction to preparing and installing ET 200PA SMART components.
General steps and considerations for installing the ET 200PA SMART system.
Step-by-step procedure for physically installing the ET 200PA SMART system components.
Instructions for preparing and mounting the DIN rail for active bus modules.
Procedure for installing active bus modules and I/O modules onto the mounting rail.
Steps to perform after physical installation, including slot numbering.
Guide on how to set the unique PROFIBUS address for the IM 650 interface module.
Introduction to electrical configuration and basic rules for connecting the ET 200PA SMART.
Instructions for connecting the PROFIBUS DP network using appropriate bus connectors.
Details on applicable FastConnect bus connectors for PROFIBUS DP.
Essential wiring rules and procedures for power supply and modules.
General wiring guidelines for power supply and IM 650 connections.
Step-by-step guide for wiring the power supply module and IM 650 with a connecting comb.
Detailed instructions for wiring the front connectors of signal modules.
Procedure for connecting shielded cables to ground using a shield connection element.
Overview of PROFIBUS DP commissioning steps.
Requirements and steps for commissioning the ET 200PA SMART as a DP slave.
Explanation of the startup process for the IM 650 interface module, including redundant configurations.
Information on the maintenance scope and limitations for the ET 200PA SMART.
Procedures for removing and installing a new power supply module.
Steps for safely removing and replacing the IM 650 interface module.
Instructions for replacing I/O modules, including module replacement in runtime.
Procedure for removing and replacing bus modules in a de-energized state.
Details on replacing fuses in specific digital output modules.
Guidance on when and how to update the IM 650 interface module firmware.
Example configuration for connecting HART field devices using the ET 200PA SMART as a HART master.
Information on supporting up to 32 bytes of I/O input data with specific analog modules.
Details on how the IM 650 supports HART primary and secondary variables.
Principles and rules for time stamping digital input signals with the IM 650.
Requirements for achieving 10 ms time stamping precision for digital input signals.
Configuration rules for high-precision time stamping with 1 ms accuracy.
Requirements and settings for time synchronization for accurate time stamping.
How time stamping functions in a redundant system with IM 650 modules.
How the IM 650 supports time synchronization on the I/O bus.
Use cases and requirements for operating IM 650 modules redundantly.
Possibilities for making system changes during runtime in redundant and non-redundant configurations.
Information about I&M data stored in modules for system checking and troubleshooting.
Explanation of the driver and diagnostic block concept for high-performance I/O interfacing.
Interpretation of IM 650 status and error messages indicated by LED displays.
Overview of S7 diagnostics structure and data for the IM 650.
Details on the structure and length of slave diagnostic data for the IM 650.
Explanation of station status bits providing an overview of DP slave status.
Information on where the master PROFIBUS address is stored in diagnostic data.
Definition and location of the manufacturer ID code for DP slaves.
Procedure for systematically evaluating slave diagnostics data.
Explanation of identifier-related diagnostics indicating faulty modules.
How module status reflects configured modules and identifier-related diagnostics.
Information on channel errors of modules and detailing of identifier-related diagnostics.
Information on H-status provided by IM 650 when used with CPU 410 in redundant configuration.
Information on interrupt types and causes triggering slave diagnostic information.
How to evaluate diagnostic and plug/pull interrupts in the DP master.
Overview of parameters, technical specs, response times, and drawings for the IM 650.
Details on assigning parameters for the IM 650 and ET 200PA SMART via HW Config.
Comprehensive technical specifications for the IM 650 interface module.
Explanation of response time and factors affecting it for the ET 200PA SMART.
Information on using the ET 200PA SMART in hazardous area zone 2 environments.
Listing of available I/O modules for the ET 200PA SMART system.
Overview of properties for ET 200PA SMART digital input modules.
Properties and article numbers for the DI 32 x DC 24 V digital input module.
Properties and article numbers for the DI 16 x DC 24 V digital input module.
Assignable parameters and their default settings for the DI 16 x DC 24 V module.
Introduction to module and channel faults for the DI 16 x DC 24 V module.
Overview of properties for ET 200PA SMART digital output modules.
Properties and article numbers for the DO 32 x DC 24 V/0.5 A digital output module.
Properties and article numbers for the DO 16 x DC 24 V/0.5 A digital output module.
Assignable parameters and default settings for the DO 16 x DC 24 V/0.5 A module.
Introduction to module and channel faults for the DO 16 x DC 24 V/0.5 A module.
Methods to protect digital modules from inductive overvoltage.
Overview of properties for ET 200PA SMART analog input modules.
Properties and article numbers for the AI 8 x 13-bit analog input module.
Configuration of measurement type and range for AI 8 x 13-bit module.
Assignable parameters and default settings for the AI 8 x 13 bits module.
Additional information regarding unused channels and PTC resistor usage.
Properties and article numbers for the AI 8 x 16 Bit analog input module.
Assignable parameters and default settings for the AI 8 x 16 Bit module.
Introduction to module and channel faults for the AI 8 x 16 Bit module.
Properties and article numbers for the AI 16 x 16 Bit analog input module.
Assignable parameters and default settings for the AI 16 x 16 Bit module.
Introduction to module and channel faults for the AI 16 x 16 Bit module.
Properties and article numbers for the AI 8 x TC/4 x RTD analog input module.
Assignable parameters and default settings for the AI 8 x TC/4 x RTD module.
Introduction to module and channel faults for the AI 8 x TC/4 x RTD module.
Overview of properties for ET 200PA SMART analog output modules.
Properties and article numbers for the AO 8 x 12 Bit analog output module.
Assignable parameters and default settings for the AO 8 x 12 Bit module.
Introduction to module and channel faults for the AO 8 x 12 Bit module.
Information on accessing current diagnostic data stored in data records.
Provides dimensional drawings for ET 200PA SMART I/O modules.
Information on compliance with relevant standards and test criteria.
Safety information and field of application for a specific analog input module.
Contact information for repair service and manufacturer details.
To Next Page