Siemens SINAMICS G150 - Page 236

Parameterlist 11/03
SINAMICS G150
Parameterlist-
2 Operating Manual
1050 - Active motor potentiometer setpoint ............................................................................... 6-8
1050 - Motor potentiometer speed setpoint downstream of ramp generator........................... 6-24
1080 - Minimum speed............................................................................................................... 7-3
1082 - Speed limit ...................................................................................................................... 7-4
1083 - Speed limit positive direction of rotation ......................................................................... 7-4
1086 - Speed limit negative direction of rotation ........................................................................ 7-4
1091 - Suppression speed 1 ......................................................................................................7-8
1092 - Suppression speed 2 ......................................................................................................7-8
1093 - Suppression speed 3 ......................................................................................................7-8
1094 - Suppression speed 4 ......................................................................................................7-8
1101 - Suppression speed bandwidth........................................................................................ 7-8
1112 - Speed setpoint after minimum limit................................................................................. 7-3
1114 - Speed setpoint upstream of ramp generator .................................................................. 6-8
1119 - Resulting speed setpoint.................................................................................................6-8
1120 - Ramp generator ramp-up time........................................................................................ 7-6
1121 - Ramp generator ramp-down time ................................................................................... 7-6
1130 - Ramp generator start rounding time ............................................................................... 7-6
1131 - Ramp generator end rounding time ................................................................................ 7-6
1200 - Flying restart operating mode ......................................................................................... 9-8
1202 - Flying restart detection current ....................................................................................... 9-8
1203 - Flying restart search rate ................................................................................................ 9-8
1210 - Automatic restart mode...................................................................................................9-5
1211 - Automatic restart starting attempts ................................................................................. 9-6
1212 - Automatic restart waiting time first starting attempt ........................................................ 9-6
1213 - Automatic restart waiting time increment........................................................................ 9-6
1240 - Vdc controller configuration.............................................................................................9-3
1242 - Vdc-max controller switch-on level ................................................................................. 9-3
1243 - Vdc-max controller dynamic factor.................................................................................. 9-3
1250 - Vdc controller proportional gain ...................................................................................... 9-3
1251 - Vdc controller integral time.............................................................................................. 9-4
1252 - Vdc controller derivative time.......................................................................................... 9-4
1254 - Vdc-max controller automatic detection of ON level....................................................... 9-4
1480 - Speed controller output................................................................................................... 8-4
1482 - I component of speed controller...............................................................................6-8, 8-4
1508 - Speed controller output................................................................................................... 6-8
2000 - Reference speed............................................................................................................. 6-9
2001 - Reference voltage ........................................................................................................... 6-9
2002 - Reference current ........................................................................................................... 6-9
2003 - Reference torque ............................................................................................................ 6-9
2004 - Reference power............................................................................................................. 6-9
2050 - PROFIBUS setpoint ........................................................................................................6-8
4022 - Status of TM31 digital inputs......................................................................................... 10-6
4047 - Status of TM31 digital outputs ...................................................................................... 10-6
4052 - Current input voltage/current ........................................................................................ 6-21
4052[0] - Analog input 0 [V, mA] ................................................................................................6-8
4052[1] - Analog input 1 [V, mA] ................................................................................................6-8
4053 - Smoothing time constant analog inputs ........................................................................ 6-22
4055 - Current per-unit input value .......................................................................................... 6-22
4055[0] - Analog input 0, scaled................................................................................................. 6-8
4055[1] - Analog input 1, scaled................................................................................................. 6-8
4056 - Analog input type .......................................................................................................... 6-21
4057[0] - Value x1 for the analog input characteristic.............................................................. 6-27
4058[0] - Value y1 for the analog input characteristic.............................................................. 6-27
4059[0] - Value x2 for the analog input characteristic.............................................................. 6-28
4060[0] - Value y2 for the analog input characteristic.............................................................. 6-28