Page 4
EN
Operating instructions table of contents
Operating instructions table of contents
1. Safety instructions 42
2. Lubricants 42
3. Transport, delivery, and storage 43
3.1 Lubrication units 43
3.2 Electronic and electrical devices 43
3.3 General notes 43
4. Assembly 44
4.1 Information on assembly 44
4.2 Assembly procedure for KFG (S) (C)
pump units 44
4.3 Dismantling and disposal 44
5. Design 45
5.1 General information 45
5.2 Design 45
5.2.1 Pump housing 45
5.2.2 Lubricant reservoir 45
5.2.3 KFGS control unit 46
5.3 KFG-pump units 46
5.4 KFGS-pump units 46
5.5 KFGC (CAN bus) 47
5.6 Images of pump units 48
6. Functional description in
progressive systems 49
6.1 Functional description of progressive
systems with KFG pump unit 49
6.1.1 Pump element 49
6.1.2 Pressure regulating valve 49
6.2 Functional description of progressive
system with a KFGS pump unit 50
6.3 Functional description of progressive
system with KFGC (CAN bus) pump unit 51
6.3.1 Explanations of the lubrication
process and lubrication cycle 51
6.3.2 Modes of operation 53
6.3.2.1 Automatic control unit 53
6.3.2.2 Semi-automatic control unit 54
6.3.2.3 Control via CAN commands 54
6.3.3 Monitoring functions 55
6.3.3.1 System monitoring 55
6.3.3.2 Fill level monitoring 55
6.3.3.3 Monitoring lubrication cycle via
piston detector 56
6.3.3.4 Monitoring signal cables for cable
breakage and monitoring valves and
piston detectors 56
6.3.3.5 Monitoring switching outputs for
short circuits 57
6.3.3.5 Monitoring power consumption
of the pump motor 57
6.3.3.7 Monitoring unit temperature 58
6.3.4 Display and documentation
functions 58
7. Commissioning 59
7.1 General commissioning 59
8. Display and control elements of
control screen 60
8.1 KFGS series 60
8.1.1 Three-digit LED display 61
8.1.2 LED display 63
8.1.3 Pushbutton operation 64
8.2 KFGC series (CAN bus) 65
9. KFGS display mode 67
9.1 KFGS series 67
10. KFGS programming 69
10.1 Start programming mode 69
10.2 Change lubrication interval times 69
10.4 Change operating modes 72
10.5 Change access code 73
10.6 Programming ranges 74
10.7 Display ranges 74
11. KFGS operating modes 75
11.1 Timer operation 75
11.2 Counter operation 75
11.3 No system monitoring 75
11.4 With system monitoring 75
11.5 Fill level monitoring 76
11.6 Monitoring via piston detector 76
12. Shutdown 77
12.1 Temporary shutdown 77
12.2 Permanent shutdown 77
13. Maintenance 78
13.1 General information 79
13.2 Service 79
14. Operational and pump faults 81
14.1 KFGS operational malfunctions 81
14.1.1 General information 81
14.1.2 Display faults 81
14.1.4 Fault types 82
14.1.5 Recording fault times 83
To Next Page
Loading...
Need help?
General
