Need help?Do you have a question about the SOMMER STArter and is the answer not in the manual?
General| Power Supply | 220-240V AC |
|---|---|
| Motor Voltage | 24V DC |
| Max. Gate Weight | 300 kg |
| Protection Class | IP44 |
| Manufacturer | SOMMER |
| Category | Gate Opener |
| Model | STArter |
| Control Options | push button |
Explains symbols used in the manual for attention and information.
Provides essential safety guidelines for installation and operation.
Details recommended storage conditions for the operator.
Brief overview of operational safety requirements.
Safety advice for using radio remote controls.
Information about the operator's type plate.
Specifies the intended purpose and limitations of the operator.
Defines the maximum dimensions for gate wings compatible with the operator.
Lists key technical specifications of the operator.
Provides physical dimensions of the operator in millimeters.
Crucial safety warnings before starting assembly.
Lists the components included in the complete set and single operator package.
Specifies the necessary tools for installation.
Recommends safety gear for installation tasks.
Provides practical advice and important information for successful installation.
Covers essential pre-installation steps and gate readiness checks.
Mandatory safety precautions during installation.
Guidance for installing the operator directly on the ground.
Details on creating a suitable foundation for the operator.
Steps for measuring and installing the operator console.
Important notes regarding console dimensions and angles.
Procedure for mounting the operator onto the console.
Instructions for attaching the gate racks to the operator's pinion.
Guidance on installing extra rack sections for longer gates.
Instructions for connecting the earth wire.
Details for connecting the operator to the mains power supply.
Notes on the operator's default installation side and gate opening direction.
Formula for calculating gate wing length for right-hand installations.
Formula for calculating gate wing length for left-hand installations.
Procedure to set the gate's fully closed end position.
Procedure to set the gate's fully open end position.
How to connect external buttons or key switches to the operator.
Explains the different functions assignable to button 2.
Essential safety precautions before working with accessories.
Diagrams and instructions for connecting photo cells.
Details for connecting an optional safety contact strip for STArter+.
Wiring instructions for an 8.2 kohm electrical safety contact strip.
Instructions for connecting an optoelectronic safety contact strip.
Safety warnings prior to connecting accessories.
Details for connecting warning lights and power supply.
Information on the floating relay output for external signals.
Instructions for connecting an external antenna to improve range.
Overview of TorMinal interface and special operator functions.
Initial setup steps and safety warnings for commissioning.
Diagram and explanation of the control system components.
Critical safety warnings related to commissioning the operator.
Explains the automatic force setting process for the operator.
Procedure to lock the operator and secure the gate manually.
Steps to reset the control unit and delete force values.
Guide to setting the force tolerance for safety and obstacle detection.
How to test and verify the force tolerance settings.
Step-by-step guide to programming remote control transmitters.
Procedure for clearing all stored radio codes from the receiver.
Safety regulations applicable to radio system operation.
Description of radio receiver LEDs and buttons.
Method for teaching handheld transmitters to the radio receiver.
How to exit the radio receiver's teach-in mode.
Procedure to remove a specific handheld transmitter's code.
Steps to delete a specific radio channel from the receiver.
Procedure to erase all stored radio transmitter data.
Instructions for programming transmitters using radio frequency.
Prerequisites, restrictions, and properties for HFL teach-in.
Explanation of DIP switch settings and their functions.
Configuration of obstacle detection using DIP switches.
Operator reaction to obstacles during gate opening.
Operator reaction to obstacles during gate closing.
Details on enabling and configuring automatic gate closing.
How the operator reacts to safety input signals.
Configuration for basic automatic closing function.
Configuration for automatic closing with photo cells.
Configuration for automatic closing with safety strip and photo cells.
Setting the prewarning time for warning lights.
Enabling or disabling the Fraba system signal evaluation.
Configuring defined opening and closing sequences.
Enabling and configuring partial gate opening.
Using two buttons for partial and full gate opening.
General safety rules for gate operation.
Instructions on how to open the gate using transmitters or buttons.
Instructions on how to close the gate using transmitters or buttons.
Procedure and safety warnings for emergency gate release.
Describes gate movement patterns based on DIP switch 7.
Steps to reset the control unit and its learned values.
Explanation of the operator's resistance to forced opening.
Detailed steps to release the operator for manual gate movement.
Procedure to lock the operator and re-engage motor control.
How the operator handles overloads and resumes operation.
Behavior of the operator after a power interruption.
How the operator reacts to obstacles during movement.
Instructions for safely replacing the operator's fuse.
Safety warnings and general maintenance precautions.
Schedule and procedures for testing safety devices.
Procedure for disassembling the operator, reversing installation steps.
Guidelines for environmentally responsible disposal of the operator.
Information regarding warranty coverage and customer support.
General advice and initial steps for resolving malfunctions.
To Next Page
