Need help?Do you have a question about the SOMMER twist 200 E and is the answer not in the manual?
General| Max Gate Width | 2.5 m |
|---|---|
| Power Supply | 230 V AC |
| Motor Voltage | 24 V DC |
| Operating Temperature | -20°C to +70°C |
| Protection Class | IP44 |
| Suitable for | Swing gates |
| Safety Features | Obstacle detection |
Explains symbols used in the manual for safety and information.
General safety instructions for installation and operation of the operator.
Instructions for proper storage of the operator to maintain its condition.
Guidelines for safe and correct operation of the gate system.
Precautions and best practices for using the radio remote control.
Information about the location of the type plate.
Defines the specific purpose and scope of the gate operator.
Lists prohibited or incorrect uses of the gate operator.
Details on using multiple operators or specific combinations.
Specifies the maximum allowed dimensions for gate leaves.
Provides detailed technical specifications and parameters of the operator.
Special considerations and precautions for using the operator with lift gates.
Illustrates the physical dimensions of the gate operator.
Explains how the gate operator functions mechanically and electronically.
Specific instructions and safety points for the gate closing process.
Information on operating the system wirelessly via transmitter.
Details the safety features integrated into the control unit.
Document detailing compliance with machinery directives for installation.
Official declaration of conformity with EU directives and standards.
Crucial safety warnings before starting installation.
Lists necessary tools for the installation process.
Specifies required PPE for safe installation.
Details the components included in the product package.
Visual representation of how components are connected.
Guidance on the correct physical placement of the operator.
Advice and best practices for a successful installation.
Table providing dimensions for optimal operator installation and angle.
Information on the included fittings and their proper use.
Details and diagrams for fitting the operator to posts or pillars.
Details and diagrams for fitting the operator to the gate leaf.
Information about optional fittings for timber posts.
Step-by-step instructions for attaching the fittings.
Guidance on mounting and protecting the control unit housing.
Instructions for safely connecting the control unit to the mains power supply.
Identification and numbering of components on the control unit PCB.
How to connect the operator motor to the control unit.
Specific wiring for outward opening gate configurations.
Procedures for setting the gate's open and close limit positions.
Detailed steps for adjusting the gate's fully open position.
Detailed steps for adjusting the gate's fully closed position.
How to engage or disengage the operator for manual movement.
Instructions for safely removing the operator cover.
Safety precautions before starting commissioning.
Setting the force sensitivity for obstacle detection.
Steps to prepare the system for continuous use after installation.
How to verify the set force tolerance.
Activating and configuring the system for ongoing operation.
Process for the control unit to learn gate movement parameters.
Identifying and resolving issues during the learning run.
Procedure to restore control unit settings to default.
Setup and configuration of the radio receiver for remote control.
Identifies components on the radio receiver module.
How to erase stored transmitter codes for security.
Steps to pair a hand-held transmitter with the receiver.
Instructions for connecting an external antenna to improve range.
Essential safety guidelines during operation.
How to manually operate the gate during a power outage.
Basic operation and factors affecting gate movement.
How the system detects and reacts to obstructions.
Adjustments for seasonal weather changes.
Step-by-step procedures for operating the gate.
Cable requirements and safety during connections.
Setting the jumper for 1-leaf or 2-leaf gate configuration.
Detailed steps to configure the jumper for gate type.
Functions of the buttons located on the control unit.
How to adjust force tolerance using the potentiometer.
Location and purpose of the radio receiver slot.
Explains the status indicators (LEDs) on the control unit.
Configuration settings using DIP switches.
Setting up and using the automatic gate closing feature.
Information on fuse types and their locations.
Connection details for the transformer.
Wiring and installation instructions for an electric lock.
Specifics on wiring an electric lock to the system.
How to connect and configure a warning light.
Wiring instructions for external buttons.
Instructions for connecting a key switch for access control.
Detailed wiring for a 4-wire photo eye safety device.
How to connect additional external devices.
Steps for connecting the cable set.
Wiring for a potential-free relay output.
Wiring the motor to the control unit.
Safety guidelines for maintenance tasks.
Schedule and procedures for testing safety devices.
Table detailing testing procedures, behaviour, causes, and remedies.
Instructions for dismantling the operator.
Guidance on environmentally sound disposal of the product.
Information on warranty terms and customer support.
Common faults and their solutions.
Further steps and advice for resolving complex issues.
To Next Page