63
HCD-FX10
Pin No. Pin Name I/O Description
49 WMD0 I External memory wait mode setting terminal (fixed at “H” in this set)
50 PAGE2 O External memory page selection signal output terminal (not used)
51 VSS — Ground terminal
52, 53 PAGE1, PAGE0 O External memory page selection signal output terminal (not used)
54 BOOT I Boot mode control signal input terminal (not used)
55 TST1 O Not used
56 BST I Boot strap signal input from the system controller
57 MOD1 I
Operation mode setting terminal “L”: enhanced mode, “H”: normal mode
(fixed at “H” in this set)
58 MOD0 I
Operation mode setting terminal “L”: single chip mode, “H”: can not use
(fixed at “L” in this set)
59 EXLOCK I PLL lock error signal and data error flag input from the digital audio interface
60 VDDI — Power supply terminal (+2.5V)
61 VSS — Ground terminal
62, 63 A17, A16 O Address signal output terminal (not used)
64 to 66 A15 to A13 O Address signal output to the S-RAM
67 GP10 I L/R sampling clock signal input terminal
68 GP9 O Read ready signal output to the system controller
69 GP8 I Channel status bit 1 input from the digital audio interface receiver
70 VDDI — Power supply terminal (+2.5V)
71 VSS — Ground terminal
72 to 75 D15 to D12 I/O Two-way data bus with the S-RAM
76 VDDE — Power supply terminal (+3.3V)
77 to 80 D11 to D8 I/O Two-way data bus with the S-RAM
81 VSS — Ground terminal
82 to 85 A9, A12 to A10 O Address signal output to the S-RAM
86 TDO O Simplicity emulation data output terminal (not used)
87 TMS I Simplicity emulation data input start and end terminal (not used)
88 XTRST I Simplicity emulation non-sync break signal input terminal (not used)
89 TCK I Simplicity emulation clock signal input terminal (not used)
90 TDI I Simplicity emulation data input terminal (not used)
91 VSS — Ground terminal
92 to 97 A8 to A3 O Address signal output to the S-RAM
98, 99 D7, D6 I/O Two-way data bus with the S-RAM
100 VDDI — Power supply terminal (+2.5V)
101 VSS — Ground terminal
102 to 105 D5 to D2 I/O Two-way data bus with the S-RAM
106 VDDE — Power supply terminal (+3.3V)
107, 108 D1, D0 I/O Two-way data bus with the S-RAM
109, 110 A2, A1 O Address signal output to the S-RAM
111 VSS — Ground terminal
112 A0 O Address signal output to the S-RAM
113 PM I PLL initialize signal input from the system controller
114, 115 SDI3, SDI4 I Audio serial data input terminal
116 SYNC I Sync/non-sync setting terminal “L”: sync, “H”: non-sync (fixed at “H” in this set)
117 TST2 I Not used
118 GP11 I (not used)
119 TST3 I (not used)
120 VDDI — Power supply terminal (+2.5V)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
To Next Page
