Strong SRT 8119 User Manual

English
WARNING: The batteries should not be recharged, disassembled, electrically short-
circuited, be mixed or used with other types of batteries. If rechargeable
accumulators instead of batteries are going to be used, we recommend
using (e.g. NiMH) types with low self-discharge to ensure long time
operation of remote control.
1.5 Usage of external USB devices
 It is recommended to use USB 2.0 storage devices. If your device is not compatible to USB 2.0
specications, the playback with your receiver might not work properly.
 If you are going to use external USB HDD (Hard Disk Drive) please consider that the power
specications might exceed the supported output of your receiver (5 V/500 mA). If so, please
connect your USB HDD to an according external power adapter.
 STRONG cannot guarantee compatibility with all types of USB storage devices.
 It is advised not to store important information on USB storage devices used with the receiver.
Always make backups of data on your USB storage device before using it with this receiver.
STRONG will not take responsibility for any loss of information or circumstances caused by loss
of information.
 Please ensure that either the USB device is already formatted to NTFS or FAT32 or format the
USB device via your receiver. Formatting requires entering the PIN code
 STRONG cannot guarantee the playback of all les although extensions are listed, as it depends
on le size, codec, bit rate and resolution.
2.0 YOUR RECEIVER
2.1 Default PIN-CODE: 0000
You can change the PIN-Code in the main menu under Channel List then Parental Lock.
Make a note of your code.
2.2 Front Panel
Fig.1
1. LED 7-segment Display: Displays channel number in operating mode or time in
standby.
2. LED Mode indicator: RED indicates that the receiver is in STAND-BY mode.
GREEN indicates that the receiver is in OPERATING
mode.
3. IR sensor: Point your remote control towards this sensor. (Hidden)
4. USB: Connector for USB devices.
2.3 Rear Panel
Fig.2
1. ANT IN To connect to your antenna for the reception of broadcast signal.
2. HDMI To connect your receiver with your TV set using an HDMI cable.
3. TV SCART To connect your receiver with your TV set using a SCART cable.
5

Strong SRT 8119 Specifications

General

Aspect ratio	4:3, 16:9
Signal source	Terrestrial
Video resolutions	720 x 576, 1280 x 720, 1920 x 1080 pixels
Supported video modes	576i, 576p, 720p, 1080i, 1080p
Analog signal format system	NTSC, PAL, VHF
Digital signal format system	DVB-T2
High Dynamic Range (HDR) supported	Yes
Personal Video Recorder (PVR) included	-
Tuner type	Analog & digital
Demodulation	16-QAM, 64-QAM, 128-QAM, 256-QAM, COFDM
Product color	Black
Audio decoders	Dolby Digital Plus
Number of tuners	- tuner(s)
Audio output channels	- channels
Audio formats supported	AC3, MPEG-1, MPEG-2
Video formats supported	H.264, HEVC/H.265, MPEG4-ASP
Flash memory	4 MB
Internal memory	64 MB
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
AC input voltage	100 - 240 V
AC input frequency	50/60 Hz
Power consumption (standby)	1 W
Power consumption (typical)	4 W
Storage temperature (T-T)	-10 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 85 %

Weight and Dimensions

Depth	91.1 mm
Width	145 mm
Height	35.5 mm
Weight	145 g