Tektronix DPO7000 Series Technical Reference

Specifications (MSO70000/C Series, DSA/DPO70000B/C Series, and DPO7000 Series)
Table 1-5: Digital acquisition specifications (MSO70000/C Series) (cont.)
Characteristic Description
Low speed serial trigger threshold
accuracy, typical
±(3% of setting ±125 mV) relative to the probe tip input
+20 m V/°C from the operating temperature at which SPC was run
Low speed serial trigger threshold
range
-2 to +4.5 V with DI probe
-1.5 to +4 V with GP probe
Maximum low speed serial trigger
toggle rate
I
2
C: 3.4 MHz
SPI: 4.25 MHz
Maximum digital acquisition sample
rate
12.5 GS/s
Maximum record length, sample mode
The maximum record length depends on the number of active channels and the installed
record length options. The maximum record length is less in serial trigger mode, hi-res
mode, or when using the FIR filter.
Standard 12.5 G S/s or less 10,000,000 points (all channels)
Option 2XL installed 12.5 GS/s or less 20,000,000 points (all channels)
Option 5XL installed 12.5 GS/s or less 50,000,000 points (all channels)
Option 10XL installed 12.5 G S/s or less 125,000,000 points (all channels)
Option 20XL installed 12.5 G S/s or less 250,000,000 points (all channels)
Table 1-6: Input/output port specifications, all MSO70000/C, DSA/DPO70000B/C, and DPO7000 Series models
Cha
racteristic
Des
cription
Auxiliary Trigger input
ch
aracteristics and range
≥4
GHz models
50
Ω, ±5 V (DC plus peak AC)
<
4 GHz models
5
0 Ω, ± 5%; maximum input voltage ± 5 V (DC + peak AC)
1MΩ, ±5%, 150 V CAT1. Derate at 20 dB/decade to 9 V RMS above 200 kHz
Auxiliary Output logic polarity and
functionality
Default output is A trigger low true (a negative edge when the A trigger event occurs). You
can also program the output to A trigger high true, B trigger low or high true, disabled, force
high, and force l ow.
V
out
high
V
out
low (true)Auxiliary Output logic levels,
typical
≥2.5Vinto1MΩ load,
≥1.0 V into 50 Ω load to ground
≤0.7Vinto1MΩ load
≤0.25 V into 50 Ω load to ground
CH3 output voltage, typical
< 4 G Hz models
50 mV/div ± 20% into a 1 MΩ load
25 mV/div ±20% into a 50 Ω load
Serial data output baud rate range,
≥ 4 GHz models
Fbaud < 1250 MB. Output swing of 1010 repeating pattern at this baud will be at least 200 mV
into 50 Ω.
High speed serial clock output
frequency range,
≥ 4 GHz models
Peak-to-peak output swing at 625 MHz is at least 200 mV p-p into 50 Ω. Higher frequencies
are further attenuated by approximately 6 dB per octave above 625 MHz.
Use AC or DC coupled 50 Ω termination; AC coupling the clock provides about 10% more
amplitude.
1–52 MSO70000/C, DSA70000B/C, DPO7000B/C, DPO7000, MSO5000, DPO5000 Series

Tektronix DPO7000 Series Specifications

General

Brand	Tektronix
Model	DPO7000 Series
Category	Test Equipment
Language	English