Why is my Tormatic Garage Door Opener not responding to the hand transmitter?
If your Tormatic Garage Door Opener responds to push buttons but not the hand transmitter, it could be due to a few reasons: * The hand transmitter battery might be empty, so replace it. * The antenna might be missing or misaligned; try plugging in or aligning the antenna. * The hand transmitter might not be programmed. In this case, program the hand transmitter.
Why is the range of my Tormatic Garage Door Opener hand transmitter insufficient?
The insufficient range of your Tormatic Garage Door Opener hand transmitter could be due to: * An empty hand transmitter battery. Replace the battery. * A missing or misaligned antenna. Plug in or align the antenna. * On-site shielding of the reception signal. In this case, connect the external antenna (accessory).
What to do if my Tormatic B-1200 doesn't fully open or close?
If your Tormatic Garage Door Opener doesn't fully open or close, it could be due to: * Changes in door mechanics. Have the door checked and correct the force settings. * The closing/opening force being set too low. Have the door checked and correct the force settings. * The end position being set incorrectly. Have the end position reset.
What to do if my Tormatic Garage Door Opener drive does not move but the motor is running?
If the drive of your Tormatic Garage Door Opener does not move even though the motor is running, it is possible that the drive is disengaged. Re-engage the drive.
Why does my Tormatic Garage Door Opener open slightly after closing?
If your Tormatic Garage Door Opener opens slightly after closing, it could be because: * The door blocks just before reaching the closed position. Remove the obstruction. * The end position is set incorrectly. Have the end position CLOSE reset.
Why is my Tormatic B-1200 toothed belt or drive noisy?
If the toothed belt or drive of your Tormatic Garage Door Opener are noisy, it might be because the toothed belt is dirty or over-tightened. Clean the toothed belt and spray it with silicone spray (do not use oil-containing substances). Also, relieve the tension of the toothed belt.
Provides an overview of the product's components and their arrangement.
Details specifications like door size, weight, power, and operating parameters.
Explains the location and importance of the rating plate on the drive head.
Identifies and describes the control elements on the drive head and hand transmitter.
Crucial safety guidelines for installing the product correctly and safely.
Illustrates the drive unit and associated accessories for installation.
Lists the components typically included in the product package.
Covers safety precautions and checks before beginning installation.
Step-by-step instructions for physically mounting the drive unit.
Explains how to disengage the drive carriage for manual operation.
Details the process of connecting the drive to power and control systems.
Presents a visual overview of the electrical connection points and diagrams.
Information on connecting external devices like pulse generators and safety sensors.
Instructions for properly positioning and routing the antenna for optimal reception.
Guides through the menu-driven programming of the drive head.
Pre-programming steps required to ensure successful transmitter setup.
Instructions for programming the hand transmitter to start the drive.
Instructions for programming the hand transmitter for light control.
Procedure to remove all previously programmed hand transmitters.
Detailed steps for setting the open and close end positions of the garage door.
Explains the process of the drive learning the door's force requirements.
Procedure for verifying and testing the programmed force limits.
Access to advanced configuration menus for various functions.
Adjusting the force limits for opening and closing the garage door.
Configuration of light timing, warning, and flashing functions.
Selecting the correct door type for optimal drive performance.
Describes various operating modes like normal, ventilation, and automatic closing.
Setting the duration the door remains open in automatic close mode.
Configuration of the STOP-A input for safety devices.
Essential safety precautions to follow during the product's operation.
Step-by-step guide on how to operate the door using the hand transmitter.
Procedure for manual operation during power failure or adjustments.
Explains the meaning of different states and error codes displayed by the unit.
Procedure to reset the drive unit to its original factory configuration.
Information on how to read the drive's cycle count.
Guidelines and recommendations for testing the garage door drive.
A checklist to confirm features during the system's initial start-up.
A log for recording inspection and maintenance activities performed.
Procedure for regularly checking the force limits of the drive.
Instructions on how to clean and maintain the drive unit.
Guidance on disassembling the system in reverse order of assembly.
Instructions for environmentally sound disposal of the product components.
Manufacturer's statement regarding compliance with EC Machinery Directive.
Statement of conformity for the integrated radio system with EU directive.
General| Brand | Tormatic |
|---|---|
| Model | B-1200 |
| Category | Garage Door Opener |
| Language | English |
To Next Page
