Toshiba B-SA4T User Manual

- 5 -
 Be sure to set the [Printer Status Monitoring] as shown in the table below. The status monitor has been
disabled as default. Wrong setting disables proper printing.
 Configuration for the Status Monitor
When the [Printer Status Monitoring] is set to other than “Disabled”, it is possible to monitor the printer status
from the host computer. When this feature is not supported or is unnecessary, choose the “Disabled” for the
[Printer Status Monitoring]. Doing so reduces the load on the printer driver and increases the print efficiency.
: Any setting X: Disabled
Interface
RS-232C
*1
(Serial interface
cable)
Parallel (Printer cable)
*2
Conforming to IEEE1284
(Compatible/ECP mode)
USB
LAN／WLAN
10BASE-T／100BASE-TX
Bluetooth
Conditions
Printer model
―
Other than the
right column
CENTRO. MODE = ECP
PLUG & PLAY = ON
Ver1.1
/2.0
Standard
TCP/IP
Port（RAW）
Other Port
―
B-SX6T (305 dpi)
B-SX8T (305 dpi)

X
Not supported


X
X
B-EX4T1 (203 dpi)
B-EX4T1 (305 dpi)

X
Not supported


X
X
B-EX4T2 (203 dpi)
B-EX4T2 (300 dpi)
B-EX4T2 (600 dpi)
B-EX4D2 (203 dpi)

X
Not supported


X
X
B-EX6T1 (203 dpi)
B-EX6T1 (305 dpi)

X
Not supported


X
X
B-EX6T3 (203 dpi)
B-EX6T3 (305 dpi)

X
Not supported


X
X
B-EX4T3 (600 dpi)

X
Not supported


X
X
B-EV4 (203 dpi)
X
X
Not supported
X
X
X
X
B-EV4 (300 dpi)
X
X
Not supported
X
X
X
X
B-FV4 (203 dpi)
X
X
Not supported
X
X
X
X
B-FV4 (300 dpi)
X
X
Not supported
X
X
X
X
B-EP2DL-G

Not supported
Not supported


X

B-EP4DL-G
Not supported
Not supported
Not supported


X

B-452-R

X
Not supported


X
X
B-462-R

X
Not supported


X
X
B-852-R

X
Not supported


X
X
B-SA4T (203 dpi),
B-SA4T-CN (203 dpi),
B-SA4T (300 dpi),
B-SA4T-CN (300 dpi)

X
Not supported


X
X
B-SX4T (203 dpi),
B-SX4T-CN (203 dpi)
B-SX5T (305 dpi),
B-SX5T-CN (305 dpi)

X
○


X
X
B-SV4

X
Not supported

Not
supported
Not
supported
X
B-FP3D (203 dpi)
X
X
X


X

Notes:
1. When RS-232C (Serial interface) is used for connection, it will take time until printing starts. It is recommended to
use other interfaces as far as possible.

Toshiba B-SA4T Specifications

General

Print Method	Thermal transfer and direct thermal
Resolution	203 dpi
Print Width	104 mm
Interfaces	Serial, Parallel, USB
Optional Interfaces	Ethernet, Wireless
Barcodes	Code 39, Code 128
2D Codes	PDF417, Data Matrix, QR Code, MaxiCode
Operating Temperature	5°C to 40°C (41°F to 104°F)
Storage Temperature	-20 - 60 °C (-4 - 140 °F)
Humidity	20% to 85% (non-condensing)
Interface	USB, Serial (RS-232), Parallel, Ethernet, Wireless