CVHE-SVX005C-EN
49
Installation: Controls
This section covers information pertaining to the Symbio™
800 controller hardware. For information about the Tracer
®
AdaptiView™ display, which is used to interface with the
internal chiller data and functions provided by the
Symbio™ 800, refer to Tracer
®
AdaptiView™ Display for
Water-cooled CenTraVac™ Chillers with Symbio™
Controls User Guide (CTV-SVU004*-EN).
Symbio™ 800
The Symbio 800 controller is a factory-installed, application
specific and programmable controller designed to control
chillers and large packaged HVAC equipment. A 12 inch
user interface features a touch-sensitive color screen that
provides facility managers at-a-glance operating status,
performance monitoring, scheduling changes, and
operating adjustments. Other advanced features include
automated controller back-up, and optional features such
as secure remote connectivity, wireless building
communications, mobile device connectivity, and custom
programming with an expandable I/O.
For more information, see Symbio™ 800 Controller
Installation, Operation, and Maintenance (BAS-SVX080*-
EN).
AdaptiView™ Display
Information is tailored to operators, service technicians,
and owners. When operating a chiller, specific information
is needed on a day-to-day basis—setpoints, limits,
diagnostic information, and reports. This information is
provided through the AdaptiView display. Logically
organized groups of information — chiller modes of
operation, active diagnostics, settings and reports put
information conveniently at your fingertips.
For more information, see CenTraVac™ Water-Cooled
Chillers AdaptiView™ Display with Symbio™ Controls User
Guide (CTV-SVU004*-EN).
Tracer TU
The AdaptiView TD12 operator interface allows for daily
operational tasks and setpoint changes. However, to
adequately service chillers, Tracer
®
TU service tool is
required. (Non-Trane personnel, contact your local Trane
office for software purchase information.) Tracer TU adds a
level of sophistication that improves service technician
effectiveness and minimizes chiller downtime. This
portable PC-based service-tool software supports service
and maintenance tasks, and is required for software
upgrades, configuration changes and major service tasks.
Tracer TU serves as a common interface to all Trane
chillers, and will customize itself based on the properties of
the chiller with which it is communicating. Thus, the service
technician learns only one service interface.
The panel bus is easy to troubleshoot using LED sensor
verification. Only the defective device is replaced. Tracer
TU can communicate with individual devices or groups of
devices.
All chiller status, machine configuration settings,
customizable limits, and up to 100 active or historic
diagnostics are displayed through the service-tool software
interface.
LEDs and their respective Tracer TU indicators visually
confirm the availability of each connected sensor, relay,
and actuator.
Tracer TU is designed to run on a customer’s laptop,
connected to the Tracer
®
Symbio™ 800 control panel with
a USB cable. Your laptop must meet the following
hardware and software requirements:
• 4 GB RAM
• 1024 x 768 screen resolution
• Ethernet 10/100 LAN card
• An available USB 2.0 port
• Windows 7 Enterprise or Professional operating system
(32-bit or 64-bit)
Note: Tracer TU versions 8.6 and earlier will also
support Microsoft
®
Windows
®
XP Professional
operation system with Service Pack 3 (SP3) .
• Microsoft .NET Framework 4.8 or later
Notes:
• Tracer TU is designed and validated for this
minimum laptop configuration. Any variation
from this configuration may have different
results. Therefore, support for Tracer TU is
limited to only those laptops with the
configuration previously specified.
• For more information, see Tracer
®
TU Service
Tool Getting Started Guide (TTU-SVN01*-EN).
Figure 29. Tracer TU
To Next Page
Loading...
