TransAct Ithaca 280 - Page 314

Index iTherm
®
280 Programmer’s Guide
Page 302 Rev K
[ESC] A <n> Set variable line spacing to n/72 inch, 78
[ESC] b <n> ... Print bar code, 131, 139, 177, 178
[ESC] B <n
1
> <n
2
> … <n
i
> 0 Set vertical tab stops,
80
[ESC] Begin 12 cpi, 85
[ESC] BEL Sound buzzer, 221
[ESC] C [NUL] <n> Set form length in inches, 81
[ESC] c <n> Select color, 99
[ESC] C <n> Set form length in lines, 81
[ESC] c 3 <n> Select paper sensor(s) to output paper-
end signals, 202, 234
[ESC] c 4 <n> Select paper sensor(s) to stop printing,
201, 234
[ESC] c 5 <n> Enable/disable paper feed, 200, 234
[ESC] d <n> Feed <n> lines at current spacing, 79
[ESC] d <n> Print and feed <n> lines, 189
[ESC] D <n
1
> <n
2
> <n
3
> … <n
i
> 0 Set horizontal tab
stops, 75
[ESC] D <n
1
> … <n
k
> NUL Set horizontal tab
positions, 205
[ESC] e <n> Print and reverse feed <n> lines, 189
[ESC] E <n> Turn on/off emphasized mode, 197
[ESC] E Begin emphasized print, 102
[ESC] F End emphasized print, 103
[ESC] f Select receipt station, 112, 114
[ESC] g <0> Process user macro, 130
[ESC] g <1> Start macro record, 122, 130
[ESC] g <2> Stop macro record, 122, 130
[ESC] g <3> Stop macro record and save, 130
[ESC] G <n> Turn on/off double-strike mode, 198
[ESC] G Begin enhanced print, 102
[ESC] h <color> <length> <format> <data> Process
color graphics, 119
[ESC] h <color> <length> <format> <data> Process
horizontal graphics, 119
[ESC] H End enhanced print, 102
[ESC] I <n> Set print quality mode, 88
[ESC] i Partial knife cut, 221
[ESC] J <n> Fine line feed, 77
[ESC] J <n> Fine linefeed, 144, 145, 146, 147
[ESC] J <n> Print and feed paper, 190
[ESC] j Print and reverse feed, 190
[ESC] K <n> Print and reverse feed <n> lines, 190
[ESC] K <n
1
> <n
2
> Print single-density graphics, 115
[ESC] L <n
1
> <n
2
> Print half-speed double-density
graphics, 115
[ESC] l Electronic Journal Carbon Copy, 153
[ESC] M <n> Select character font table, 192
[ESC] m Perform a partial knife cut, 221
[ESC] p <m> <t
1
> <t
2
> Generate pulse, 223
[ESC] P <n> Begin rotated font, 89
[ESC] p 3 <n> Select paper sensor(s) to output paper-
end signals, 163
[ESC] p 4 <n> Select paper sensor(s) to stop printing,
163
[ESC] p 5 <n> Enable/disable paper feed, 162
[ESC] q <n> Query marker, 160
[ESC] Q <n> Set right margin, 206
[ESC] r <0> End rotated print, 109
[ESC] r <1> Rotate 90, 108
[ESC] r <11> Rotate 270 with two pass font, 109
[ESC] r <13> Rotate 90 with two pass font and line
formatting, 108
[ESC] r <15> Rotate 270 with two pass font and line
formatting, 109
[ESC] r <3> Rotate 270, 108
[ESC] r <5> Rotate 90 with line formatting, 108
[ESC] r <7> Rotate 270 with line formatting, 108
[ESC] r <9> Rotate 90 with two pass font, 108
[ESC] r <n> Rotate 90, 180, or 270, 106
[ESC] R <n> Select an international character set, 193
[ESC] r <n> Turn color mode on/off, 196
[ESC] R Reset horizontal and vertical tab stops, 76, 80
[ESC] S <0> Select superscript, 103
[ESC] S <1> Select subscript, 103
[ESC] s <n> Set rotated print line length, 110
[ESC] SP <n> Set right-side character spacing, 191
[ESC] t <n> Select character code table, 196
[ESC] T End superscript or subscript, 103
[ESC] U <0> Begin bi-directional print, 118
[ESC] U <1> Begin unidirectional print, 117
[ESC] U <n> Turn on/off unidirectional printing
mode, 205
[ESC] u <n
1
> <m
1
> Set rotated print line spacing, 110
[ESC] V <n> Set intercharacter spacing, 87
[ESC] V <n> Turn on/off 90 rotation mode, 198
[ESC] W <n> Double-wide, double-high mode, 100
[ESC] w <n> Enable dynamic response, 147
[ESC] x <n> Open cash drawer, 161
[ESC] X <n
1
> <n
2
> Set left/right print margin, 159
[ESC] y <11> OCR character enable, 96
[ESC] y <12> OCR character disable, 97
[ESC] y <n> Set feature control, 165
[ESC] Y <n
1
> <n
2
> Print full-speed double-density
graphics, 116
[ESC] Z <n
1
> <n
2
> Print quad-density graphics, 116
[FF] Set form feed, 81, 83
[GS] \ <n
l
> <n
h
> Set relative vertical print position in
page mode, 218
[GS] a <n> Enable/disable Automatic Status Back,
208
[GS] b <n> Turns smoothing on/off, 199
[GS] c Print counter, 226
[GS] g 0 Initialize maintenance counter, 226
[GS] g 2 Transmits maintenance counter, 227
[GS] I <n> Transmit printer ID, 222
[GS] P x y Set horizontal and vertical motion units,
222
[GS] r <n> Transmit status, 210
[GS] Start/end macro definition, 228
[GS] V <m> <n> Select cut mode and cut paper, 221
[HT] Set horizontal tab, 75, 204
[LF] Print and line feed, 189
[LF] Set line feed, 74
[SI] Begin 17 cpi, 85
[SO] Begin one-line double-wide print, 99
[SOH] <n> Begin multi-drop control, 168
[VT] Set vertical tab, 80
10 CPI Character Pitch, Beginning, 85
12 CPI Character Pitch, Beginning, 85
12 x 12 Draft Print Mode, Beginning, 88
17 CPI Character Pitch, Beginning, 85
24 CPI Character Pitch, Beginning, 85