TransAct Ithaca 280 - Quick Pcos Reference Chart

Programming Codes iTherm
®
280 Programmer’s Guide
Page 62 Rev K
Quick PcOS Reference Chart
Description
ASCII
Hex
IPCL
equivalent
code
Page
Low Level paper Motion
Line feed.
[LF]
0AH
&%LF
74
Carriage return.
[CR]
0DH
&%CR
74
Horizontal Motion
Back space.
[BS]
08H
&%BS
75
Horizontal tab.
[HT]
09H
&%HT
75
Set horizontal tab stops.
[ESC] D <n
1
>
<n
2
> ... <n
i
>
<0>
1BH,44H
none
75
Set horizontal position.
[ESC] n <n
1
>
<n
2
>
1BH,6EH
&%HP<m
1
>
<m
2
> <m
3
>
76
Set justification.
n=0 Left
n=1 Center
n=2 Right
n=8 Left (No line feed)
n=9 Center (No line feed)
n=10 Right (No line feed)
[ESC] a <n>
1BH,61H
&%JR {n=2}
&%JC {n=1}
&%JL {n=0}
76
Reset horizontal and vertical tab stops.
[ESC] R
1BH,52H
&%HV
76
Set left/right print margins.
n
1
= Left margin, n
2
= Right margin
[ESC] X
<n
1
><n
2
>
1BH,58H
none
159
Vertical Motion
Perform a fine line feed.
[ESC] J <n>
1BH,4AH
&%FM <m
1
>
<m
2
> <m
3
>
77
Set 1/8-inch line spacing.
[ESC] 0
1BH,30H
&%ST
78
Set 7/72-inch line spacing.
[ESC] 1
1BH,31H
&%SG
78
Begin variable line spacing. (Enable [ESC]
A <n>).
[ESC] 2
1BH,32H
none
79
Set variable line spacing to n/216 inch.
[ESC] 3 <n>
1BH,33H
&%SV <m
1
>
<m
2
> <m
3
>
77
Set variable line spacing to n/72 inch.
[ESC] A <n>
1BH,41H
none
78
Feed <n> lines at current spacing.
[ESC] d <n>
1BH,64H
&%FL <m
1
>
<m
2
>
79
Set vertical tab stops.
[ESC] B <n
1
>
<n
2
> <n
3
>...<n
i
>
0
1BH,42H
none
80
Vertical tab.
[VT]
0BH
&%VT
80
Form feed.
[FF]
0CH
&%FF
81
Feed to black dot
[ESC][VT]
1BH,0BH
None
83
Set top of form.
[ESC] 4
1BH,34H
&%TF
81
Set form length in lines.
[ESC] C <n>
1BH,43H
&%SL <m
1
>
<m
2
>
81
Begin auto line feed. (n=0, end n=1)
[ESC] 5 <n>
1BH,35H
&%CA {n=0}
&%MA {n=1}
82
Set form length in inches.
[ESC] C [NUL]
<n>
1BH,43H
&%SI <m
1
>
<m
2
>
81
Reverse line feed.
[ESC] ]
1BH,5DH
&%LR
82