Index iTherm
®
280 Programmer’s Guide
28-04430 Rev K Page 301
Index
[BEL] Audio alert, 161, 162
[BEL] Sound buzzer, 221
[BS] Insert back space, 75
[BS] Set back space, 204
[CAN] Clear print buffer, 160
[CR] Print and carriage return, 189
[CR] Set carriage return, 74
[DC2] Begin 10 cpi, 85
[DC4] End one-line double-wide print, 99
[DLE] [DC4] <1> <m> <t> Generate pulse in real
time, 223
[DLE] [DC4] <2> <a> <b> Executes the printer
power-off sequence, 223
[DLE] [DC4] <8> d1…d7 Clear Buffer(s), 223
[DLE] ENQ <n> Real-time request to printer, 225
[DLE] EOT <n> Transmit real-time status, 211
[ENQ] <1> Inquire Cash Drawer 1 status, 170
[ENQ] <10> Request printer reset, 171
[ENQ] <11> Request printer power cycle status, 172
[ENQ] <14> Inquire mechanical error status, 172
[ENQ] <15> Inquire printer state, 173
[ENQ] <20> Inquire all printer status, 174
[ENQ] <21> Inquire printer ID, 175
[ENQ] <22> Inquire Error Status, 176
[ENQ] <23> Inquire user-store status, 177
[ENQ] <3> Inquire receipt paper low status, 170
[ENQ] <4> Inquire receipt paper out status, 171
[ENQ] <8> Inquire cover open status, 171
[ENQ] <9> Inquire buffer status, 171
[ENQ] <n> Inquire printer status, 170
[ESC] - <1> Begin underline, 100, 102
[ESC] - <n> Turn on/off underline mode, 197
[ESC] \ <n
l
> <n
h
> Set relative print position, 203
[ESC] ! <n> Select international character set, 90, 155,
156, 157, 158
[ESC] ! <n> Select print mode(s), 197
[ESC] # <0> Begin 12 x 12 draft print, 88
[ESC] $ <n
l
> <n
h
> Set absolute print position, 203
[ESC] $ <n
l
> <n
h
> Set print position to beginning, 203
[ESC] $ Cancel user-defined characters, 96
[ESC] % <n> Select/cancel user-defined character set,
191
[ESC] % G Begin italics, 104
[ESC] % H End italics, 104
[ESC] & <y> <c1> <c2> … Define user-defined
characters, 192
[ESC] * <m> <0> <0> Set horizontal graphics mode,
120
[ESC] * <m> <n
1
> <n
2
> Print graphics in mode <m>,
116
[ESC] * <m> <nl> <nh> <dl> … <dk>Select bit-
image mode, 207
[ESC] ? <m> <n> Reassign graphic mode, 117
[ESC] ? <n> Cancel user-defined characters, 192
[ESC] @ Initialize the printer, 161, 222
[ESC] [ @ ... Double-wide, double-high italics, 101
[ESC] [ C <n> Insert Euro character, 93
[ESC] [ P <n> Set character pitch, 86
[ESC] [ S... Redefine character set, 94
[ESC] [ T <n
h
> <n
l
> Select character code page, 91
[ESC] [BEL] <n
1
> <n
2
> <n
3
> Audio alert control, 162
[ESC] [EM] B <n> Set bar code height, 140
[ESC] [EM] J <n> Set bar code justification and HRI
modes, 141
[ESC] [SI] Begin 24 cpi, 85
[ESC] [US] 1 <Name..> <0> Load item process, 123
[ESC] [US] b <Name..> <0> Begin named macro
record, 122, 124
[ESC] [US] c <Name..> <0> Save user-defined
characters, 123, 125
[ESC] [US] d <Name..> <0> Delete item from user
store, 127
[ESC] [US] e <Name..> <0> End name macro record,
125
[ESC] [US] e <Name..> <0> Remove item from user
store, 123
[ESC] [US] e <Name..> <0> Stop name macro record,
122
[ESC] [US] f ALL <0> Flush user store, 124, 127
[ESC] [US] l <Name> <0> Load macro/character, 126
[ESC] [US] m <Name..> <0> Save macro data, 125
[ESC] [US] m <Name..> Save macro data, 122
[ESC] [US] q <Name..> <0> Query user store, 128
[ESC] [US] r <Name> <0> Run macro data, 126
[ESC] [US] s <Name..> <0> Flag as a start-up macro,
123
[ESC] [US] s <Name..> <0> Flag start-up macro, 126
[ESC] ] Reverse line feed, 82
[ESC] ^ <n> Print control character, 93, 196
[ESC] { <n> Turn on/off upside-down print mode,
198
[ESC] { Electronic Journal Begin, 152
[ESC] < <n> Enable data pass through, 164
[ESC] < <n> Enable print suppress, 164
[ESC] < Return home, 206
[ESC] <n> <n
1
> <n
2
> Set horizontal position, 76
[ESC] = <n> Select peripheral device status, 224
[ESC] = <y> <c
1
> <c
2
> … Define user-defined
characters, 95
[ESC] = y c
1
c
2
…Define user-defined characters, 123
[ESC] > <n> Enable user-defined characters, 96
[ESC] 0 Set line spacing to 27/216 inch, 78
[ESC] 1 <n> Set left margin, 206
[ESC] 1 Set line spacing to 7/72 inch, 78
[ESC] 2 Enable variable line spacing, 79
[ESC] 2 Select default line spacing, 191
[ESC] 3 <n> Set line spacing, 191
[ESC] 3 <n> Set line spacing to n/216 inch, 77
[ESC] 4 Begin italics, 199
[ESC] 4 Set top of form, 81
[ESC] 5 <01> Begin auto line feed, 82
[ESC] 5 End italics, 199
[ESC] 8 Disable paper out sensor, 159
[ESC] 9 Enable paper out sensor, 159
[ESC] a <n> Select justification, 204
[ESC] a <n> Set justification, 76
To Next Page
Loading...
