Need help?Do you have a question about the Wassp DRX and is the answer not in the manual?
Blank section for user notes.
Details the key features of the DRX multibeam configuration.
Describes the components of the complete WASSP multibeam sounder system.
Details the recommended sensor and component configuration for the WASSP system.
Outlines the components of a typical survey system setup with the DRX.
Lists the standard and kit-dependent parts required for DRX installation.
Discusses supported transducer types and their configurations.
Provides guidance on selecting an optimal location for the DRX system.
Details considerations and procedures for mounting the DRX unit.
Explains how to power the DRX unit on and off using the power button or remote switch.
Describes the 4 LEDs indicating the status of the DRX system.
Covers checking DRX versions, upgrading, and restoring settings.
Details how to reset all DRX settings to factory default values.
Explains how to set a fixed IP address for the DRX unit.
Describes how to enable optional DRX features using license keys.
Guides on taking accurate ship measurements for sensor calibration.
Allows selection, saving, and retrieval of preconfigured sensor setup options.
Used for configuring physical DRX ports to receive sensor data.
Configures sensor position and port connection on the DRX.
Sets up external data types required for DRX operation.
Enables/disables attitude corrections and adjusts transducer draft.
Used for syncing DRX transmit to other acoustic equipment via key pulse.
Details configuring the DRX to act as a key pulse slave for transmission.
Explains how to configure the DRX to transmit a key pulse signal as a master.
Configures Rx blanking to remove potential interference during key pulse input.
Describes advanced key pulse functionality, KP timeout, and jitter.
Configures PPS input for sensor time data synchronization.
Allows uploading DRX Geoid files for calculating sea level.
Essential tests for correctly configuring the DRX and ensuring data accuracy.
Details running patch tests to account for GPS time delay.
Guides on calculating and applying roll offset for accurate data.
Explains how to compute pitch offset using distinct objects and vessel travel.
Guides on determining heading correction using high accuracy positioning.
Describes how to check configuration after completing on-water patch tests.
Details connecting the DataManager to the DRX for RPM functionality.
Explains connecting user interfaces to DataManager RPM.
Provides example RPM setup configurations for different software.
Guides on installing and connecting WASSP CDX to the DRX.
Explains how to connect Maxsea TimeZero Plot to the DRX.
Details connecting HYPACK to the DRX for data acquisition.
Provides dimensional drawings for the DRX-32 model.
Provides dimensional drawings for the DRX-46 model.
Details the interconnection diagram for the DRX-32 model.
Details the interconnection diagram for the DRX-46 model.
Presents detailed technical specifications for the DRX unit.
Contains various cable diagrams for DRX connections.
Shows the wiring diagram for the transducer RX cable.
Illustrates the fitting of the transducer cable restrainer.
Details the assembly procedure for the transducer TX cable socket.
Provides connection details for the RS-232 connector.
Shows the pinout and connection details for the RS-422-A connector.
Provides pinout and connection details for the RS-422-B connector.
Details the NMEA 0183 connector pinout and example connections.
Describes the AUX connector for remote power control.
Explains the AUX connector for Key Pulse inputs.
Details the AUX connector for Key Pulse outputs.
Shows connection details for the DC power supply.
Details standard Gigabit Ethernet wiring.
Shows NMEA2K connector pinout and specifications.
Details the fan connector pinout and power specifications.
Step-by-step guide for connecting the transducer to IP67 DRX units.
Lists sensors and sentences supported by the DRX for configuration.
Lists sensors and their configurations supported by the DRX.
Lists NMEA and serial sentences supported by the DRX.
Details NMEA 0183 sentences output by the DRX.
Lists NMEA 2K sentences supported by the DRX.
Notes on satellite compass and IMU performance.
Details measurement locations for transducer, GPS antenna, and motion sensor.
Shows transducer measurement locations for different models.
Refers to GPS installation manual for antenna measurement location.
States IMU measurement location is typically central on the IMU.
Explains how to calculate sea level height using GPS and geoid data.
Details calculating sea level height using DRX Geoid files.
Explains calculating sea level height using internal GPS Geoid.
Describes how to enable RTK tide mode for sea level height calculation.
Explains how to enable auto control features within the CDX software.
Tracks changes in DRX interconnection across different back panel versions.
Provides definitions for terms used in the DRX installation manual.
Information on warranty, technical support, and available resources.
Details the one-year limited warranty for DRX products.
Provides information on obtaining maintenance, repair, and technical support.
Links to manuals, software updates, knowledge base, and drawings.
General| Brand | Wassp |
|---|---|
| Model | DRX |
| Category | Transceiver |
| Language | English |
To Next Page