Wood-mizer LX50 G14S User Manual (English)

Other manuals for Wood-mizer LX50 G14S

Questions and Answers:

D
Dr. Katie Smith MDAug 17, 2025
Why am I getting wavy cuts with my Wood-mizer LX50 G14S?
- B
  brandy99Aug 18, 2025
  Wavy cuts in your lumber are often due to several factors. It may be because you're feeding the wood too quickly, so try reducing the feed speed. The blade might not be sharpened correctly, so resharpen it. Check if the blade guides are adjusted correctly and adjust if needed. Sap buildup can also cause this, so try using Water Lube. Finally, a tooth set problem can be the reason, so resharpen and reset the blade.
S
Samantha MorrisonAug 20, 2025
Why is the lumber not square when using my Wood-mizer LX50 G14S?
- W
  Wendy RobertsAug 20, 2025
  If the lumber isn't square, several things could be off. First, the vertical side supports might not be square to the bed, so adjust them. The blade might not be parallel to the bed rails, so adjust the bed rails. Sawdust or bark between the log/cant and the bed can also cause this, so remove any particles. Finally, a tooth set problem can be the reason, so resharpen and reset the blade.
F
Felicia RomanAug 23, 2025
What causes the blade to not track right on the wheels of my Wood-mizer Saw?
- S
  Sonya PotterAug 23, 2025
  If the blade isn't tracking correctly on the wheels of your Wood-mizer Saw, the blade wheel might be improperly adjusted, so readjust it. Flat or worn blade wheel belts can also cause this; replace the belts.
C
carl44Aug 25, 2025
Why do drive belts wear prematurely on Wood-mizer Saw?
- J
  Jessica MackAug 26, 2025
  Drive belts on your Wood-mizer Saw may wear prematurely or jump if the engine/motor and drive pulleys are out of alignment. Align the pulleys to resolve this issue.
K
kgarciaAug 27, 2025
What to do if sawdust builds up on the track of my Wood-mizer LX50 G14S?
- M
  Matthew MorganAug 27, 2025
  Sawdust buildup on the track can occur for a few reasons. You might be using too much lubrication, so apply white lithium grease instead. The wipers could be worn; try adjusting them for firmer contact with the track or replace them. The track itself might be sticky, so clean it and apply silicone spray.
B
Brent ValdezAug 30, 2025
How to fix height adjustment that jumps on Wood-mizer LX50 G14S Saw?
- W
  whitneyjulianAug 30, 2025
  If the height adjustment is jumping or stuttering, it could be due to a few reasons. The lift cable might be improperly adjusted, so adjust the lift cable. The vertical wear pads might be too tight, so adjust the pads. Alternatively, the lift cable could be too loose, so replace or adjust the lift cable.
D
Dawn HarperSep 1, 2025
Why do I get wavy cuts with my Wood-mizer Saw?
- L
  lisajohnsonSep 1, 2025
  Wavy cuts on your Wood-mizer Saw can occur due to several reasons. Check if your feed speed is excessive and reduce it. The blade might be improperly sharpened, so resharpen it. Ensure your blade guides are properly adjusted. Sap buildup on the blade can also cause this, so use Water Lube. Another potential cause is a tooth set problem, requiring you to resharpen and reset the blade.
J
John PooleSep 4, 2025
What to do if boards are thick or thin on the ends with my Wood-mizer Saw?
- C
  Cheryl ReeseSep 4, 2025
  If you're getting boards that are thick or thin on the ends or in the middle with your Wood-mizer Saw, it could be due to stress in the log, causing it to not lay flat on the bed. After squaring the log, take equal cuts off opposing sides, remove a board from the top, turn the log 180 degrees, and repeat, keeping the heart in the middle for your last cut. Another reason might be an incorrect tooth set, requiring you to resharpen and reset the blade. Misaligned bed rails can also cause this issue, so realign the bed.
C
Cynthia NielsenSep 6, 2025
Why do blades dull quickly on my Wood-mizer Saw?
- H
  hendersonanthonySep 6, 2025
  Blades on your Wood-mizer Saw might be dulling quickly due to several factors. Dirty logs can cause this, so clean or debark logs, especially on the entry side of the cut. Overheating during grinding can soften the teeth; grind just enough metal to restore sharpness and use water/coolant while sharpening. Poor sharpening techniques can also be a factor, so ensure the tips of the teeth are sharpened properly.
M
Martha BerrySep 9, 2025
What causes lumber to not be square when using my Wood-mizer Saw?
- S
  Samuel LewisSep 9, 2025
  If the lumber from your Wood-mizer Saw isn't square, it could be because the vertical side supports aren't square to the bed, so adjust them. The blade might not be parallel to the bed rails, requiring you to adjust the bed rails. Sawdust or bark between the log/cant and bed can also cause this, so remove any particles. A tooth set problem could also be the reason; resharpen and reset the blade.

Wood-mizer LX50 G14S Specifications

General

Power	14 HP
Fuel Type	Gasoline
Starting System	Electric Start
Max log diameter	26 inches (66 cm)
Blade Length	144 inches
Blade Width	1.25 inches
Blade Thickness	0.042 inches (1.07 mm)