Xantrex Freedom XC 2000

Questions and Answers

R
Robin MooreJul 27, 2025
What to do if my Xantrex Freedom XC 2000 shows no output voltage and the status LED is red?
- K
  Karen BrandtJul 27, 2025
  If your Xantrex Inverter shows no output voltage and the status LED is red, it could be due to several reasons: * **Low input voltage (error code E01):** Verify the unit is connected to a 12V battery. Check the DC connections and the cable. Recharge the battery. * **High input voltage (error code E02):** Verify the unit is connected to a 12V battery. Check the voltage regulation of the external charging system. * **Unit overload or AC output short circuit (error code E03):** Reduce the load to ensure it does not exceed the output rating. * **Thermal shutdown (error code E04):** Allow the unit to cool off, reduce the load if continuous operation is required, and improve ventilation. Also, ensure that the inverter/charger’s ventilation openings are not blocked.
A
Alice WilliamsJul 31, 2025
What to do if my Xantrex Freedom XC 2000 has no output voltage shown on the LCD screen, but the green status LED for Battery mode is illuminated?
- G
  garrettpageJul 31, 2025
  If your Xantrex Inverter shows no output voltage on the LCD screen but the green status LED for Battery mode is illuminated, consider the following possibilities: * The RCBO (if installed downstream) or supplementary breaker might have tripped. Check the load and reset the RCBO or supplementary breaker. * The circuit breaker on the AC load panel or AC output disconnect might have tripped. Reset the circuit breaker or check the AC output disconnect circuits. * The battery voltage may be too low to start inverting (depending on the setting). The LCD screen may display the DC voltage as 000. Check the DC connections and cable, and recharge the battery.
M
Megan LeeAug 5, 2025
What to do if my Xantrex Freedom XC 2000 shows no output voltage on the LCD screen and neither of the green status LEDs is illuminated?
- W
  Wendy HartAug 5, 2025
  If your Xantrex Inverter displays no output voltage on the LCD screen, and neither green status LED is lit, here's what you should check: * AC shore power may not be available or within the operating range, and the inverter/charger is OFF. Check the AC shore power and turn the inverter/charger ON. * AC shore power may not be available, and the inverter/charger switched OFF due to a shutdown lasting more than 30 seconds. Check AC shore power and battery voltage. Turn the inverter/charger ON and look at the LCD screen for any error code.
J
James GrossAug 9, 2025
Why does my Xantrex Inverter fan turn on and off during AC shore power mode?
- J
  Jacob Thompson PhDAug 9, 2025
  If the fan in your Xantrex Inverter turns on and off during AC shore power mode, it is likely because the battery is discharged and the AC pass-through current is high. This is normal operation, so there is no need to be alarmed.
K
Karina GarrettAug 13, 2025
Why does my Xantrex Inverter fan turn on and off during inverter mode?
- S
  Susan MedinaAug 13, 2025
  If the fan in your Xantrex Inverter turns on and off during inverter mode, it is likely because the inverter is running continuously at high power. This is normal, as the fan activates automatically under these conditions.
G
Gerald SmithAug 18, 2025
What to do if my Xantrex Inverter shows no output voltage and the status LED is not lighting up?
- E
  Elizabeth GreenAug 18, 2025
  If your Xantrex Inverter shows no output voltage and the status LED is not lighting up, it could be due to the ignition lock (ACC) signal not being present. If the ignition control feature is in use, ensure the vehicle’s ignition is On and the ignition control switch on the front of the Freedom XC unit is On (|).
S
Sarah QuinnAug 21, 2025
What to do if some devices cannot be detected when load sensing on my Xantrex Inverter?
- P
  Paul KellerAug 21, 2025
  If some devices cannot be detected when load sensing with your Xantrex Inverter, especially small fluorescent lights, you can either use a small companion load like a light bulb rated for more than 25 W to bring the Freedom XC out of power save mode, or program the Freedom XC to remain on by disabling power save mode.

Summary

Important Safety Instructions

Understanding Hazard Levels

Defines DANGER, WARNING, and CAUTION hazard levels.

Product Safety Information

General Safety Precautions

Key safety rules for using the inverter/charger.

Electrical Shock and Fire Hazards

Critical information on preventing electrical shock and fire.

Additional Safety Precautions

Lithium Ion Battery Safety

Specific safety warnings for lithium ion batteries.

Precautions When Working With Batteries

Safety guidelines for battery handling and maintenance.

Unit Placement and Handling

Fire and Burn Hazards

Hazards related to unit placement and handling.

Installation

Before You Begin Installation

Installation Codes and Regulations

Basic Installation Procedures

Step-by-step guide for installing the Freedom XC unit.

Installation Procedures

Installation Tools and Materials

Designing the Installation

Choosing a Location for the Unit

Mounting the Unit

AC Wiring and Connections

Connecting AC Input Wires

Detailed procedure for connecting AC input wiring to the unit.

AC Output Connections

Steps for connecting the AC output to an existing circuit.

DC Wiring and Connections

Connecting DC Cables

Procedure for connecting the DC cables to the unit and battery.

DC Grounding

Guidelines and requirements for DC grounding connections.

Ports and Testing

Testing Your Installation

Procedures for verifying the installation and unit operation.

Marine Installation

Operation

Adjusting Settings

Battery Mode Operation

Turning Inverter Operation ON;OFF

Grid Mode Operation

Battery Charger Functions

3-Stage Charging Algorithm

Mode Transitions and Limits

Custom Battery Settings

Transitions Between Modes

Troubleshooting

Pre-service Checklist

Steps to take before contacting customer support for issues.

Warning Messages and Error Codes

Explains audible alarms and error codes displayed on the unit.

Troubleshooting Reference

Common problems, causes, and solutions in a table format.

Xantrex Freedom XC 2000 Specifications

General

Continuous Power	2000W
Surge Power	4000W
Input Voltage	12V DC
Output Voltage	120V AC
Output Frequency	60 Hz
Waveform	Pure Sine Wave
Efficiency	90%
Operating Temperature	-4°F to 140°F (-20°C to 60°C)
Transfer Time	20ms