Xerox Phaser 3635MFP User Manual

2-21
Phaser 3635MFP
07-110, 07-130
Status Indicator RAPs
Draft 4
07-110 Paper Empty at Tray 1 RAP
07-110 The machine has detected that tray 1 is empty.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Refer to Wiring Diagram 2. Perform the following:
1. Remove tray 1. Check that the tray 1 paper empty sensor actuator, moves freely and is
not damaged.
2. Enter dC330 code 07-110. Check the tray 1 paper empty sensor (Q07-110), PL 10.22
Item 1. If necessary, install a new tray 1 paper empty sensor, PL 10.22 Item 1.
3. Check the wiring between the tray 1 paper empty sensor and CN4 on the Main PWB.
4. If necessary:
a. Install a new front duplex guide assembly, PL 10.22 Item 15.
b. Perform OF7 Main PWB Check RAP.
07-130 Jam 0 From Tray 1 RAP
07-130 The lead edge of the paper failed to actuate the registration sensor within the correct
time after paper was fed from tray 1.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: The front cover assembly interlock switch must be closed to supply +24V to the motors
and clutches.
Refer to Wiring Diagram 7 and Wiring Diagram 8. Perform the following:
1. Pull out tray 1. Remove all jammed paper.
2. Check the paper path for damage or obstructions.
3. Remove the tray 1 pickup roll, PL 10.22 Item 14. Check that the pickup roll is clean. If
necessary, install a new pickup roll, PL 10.22 Item 14.
4. Check the retard pad on tray 1. If necessary, install a new retard pad assembly, PL 8.10
Item 20.
5. Check that the following components are clean and rotate freely, install new components
as necessary:
• Registration roll, PL 8.25 Item 3.
• Registration roll idler, PL 8.25 Item 17.
6. Check that the registration sensor actuator, PL 8.25 Item 14 moves freely and is not dam-
aged. If necessary, install a new registration sensor actuator, PL 8.25 Item 14.
7. Enter dC330 code 08-500. Check the registration sensor (Q08-500). If necessary, install a
new HVPS, PL 1.10 Item 3.
NOTE: The registration sensor is mounted on the HVPS.
8. Enter dC330 code 04-100 to run the main BLDC motor.
9. Check the wiring between the main BLDC motor and CN38 on the Main PWB.
10. While the main BLDC motor runs, stack the code 08-810 to energize the tray 1 pickup
clutch (CL08-810). Check that the tray 1 pickup roll, PL 10.22 Item 14 rotates. Install new
components as necessary, PL 8.25 and PL 10.22.
11. Check the wiring between the tray 1 pickup clutch and CN35 on the Main PWB.
12. While the main BLDC motor runs, stack the code 08-850 to energize the registration
clutch (CL08-850). Check that the registration roll, PL 8.25 Item 3 does not rotate. Install
new components as necessary, PL 8.25.
13. Check the wiring between the registration clutch and CN35 on the Main PWB.
14. If necessary:
• Install a new front duplex guide assembly, PL 10.22 Item 15.
• Perform OF7 Main PWB Check RAP.

Xerox Phaser 3635MFP Specifications

General

Network ready	Yes
Dimensions (WxDxH)	472 x 478 x 54 mm
Networking features	Fast Ethernet
All-in-one functions	Copy, Fax, Print, Scan
Color all-in-one functions	Scan
Print technology	Laser
Maximum resolution	1200 x 1200 DPI
Time to first page (black, normal)	9 s
Print speed (black, normal quality, A4/US Letter)	33 ppm
Digital sender	No
Maximum duty cycle	75000 pages per month
Page description languages	PCL 5e, PCL 6, PostScript 3
Copier resize	25 - 400 %
Maximum copy resolution	600 x 600 DPI
Maximum number of copies	99 copies
Scan to	E-mail, Fax, FTP, USB
Maximum scan area	220 x 300 mm
Image formats supported	JPG, TIF
Faxing	Mono faxing
Modem speed	33.6 Kbit/s
Fax coding methods	JBIG, JPEG, MH, MMR (Fax coding method), MR
Fax speed dialing (max numbers)	199
Paper input type	Paper tray
Total input capacity	550 sheets
Total output capacity	250 sheets
Maximum number of input trays	3
Auto document feeder (ADF) input capacity	60 sheets
Maximum print size	216 x 356 mm
Paper tray media types	Bond paper, Envelopes, Labels, Plain paper, Recycled paper, Transparencies
ISO A-series sizes (A0...A9)	A4, A5
Maximum ISO A-series paper size	A4
Display	LCD
Market positioning	Business
Standard interfaces	Ethernet, USB 2.0
USB 2.0 ports quantity	1
Security algorithms	802.1x RADIUS, HTTPS
Supported network protocols (IPv4)	FTP, HTTP, HTTPs, LPR, SNMPv1, SNMPv2, SNMPv3, TCP/IP, UDP
Internal memory	512 MB
Card reader integrated	-
Internal storage capacity	80 GB
Sound pressure level (printing)	59 dB
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	15 W
Power consumption (PowerSave)	55 W
Power consumption (average operating)	600 W
Mac operating systems supported	Mac OS X 10.3 Panther, Mac OS X 10.4 Tiger, Mac OS X 10.5 Leopard, Mac OS X 10.6 Snow Leopard, Mac OS X 10.7 Lion
Windows operating systems supported	Windows 2000, Windows 2000 Professional, Windows Vista Business, Windows Vista Business x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Professional, Windows XP Professional x64
Storage temperature (T-T)	10 - 32 °C
Operating temperature (T-T)	16 - 30 °C
Storage relative humidity (H-H)	20 - 80 %
Operating relative humidity (H-H)	30 - 70 %
Sustainability certificates	ENERGY STAR
Certification	CE, FCC, RoHS