EasyManuals Logo

Xylem hydrovar User Manual

Xylem hydrovar
116 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #4 background imageLoading...
Page #4 background image
6.4.1 EMC requirements......................................................................................................30
6.4.2 Wiring the cables........................................................................................................30
6.4.3 RFI switch..................................................................................................................... 31
6.5 AC mains and motor connection terminals....................................................................32
6.5.1 AC Mains (power supply) connection...................................................................... 32
6.5.2 Motor connection....................................................................................................... 33
6.6 Control terminals............................................................................................................... 34
6.6.1 Motor sensor connection...........................................................................................35
6.6.2 Input for emergency basic operations.....................................................................36
6.6.3 Digital and analog I/O................................................................................................36
6.6.4 RS485 connection.......................................................................................................37
6.6.5 Status relays.................................................................................................................37
6.7 Premium card terminals.................................................................................................... 38
6.7.1 Digital and analog I/O (X3)........................................................................................38
6.7.2 Relays (X4)................................................................................................................... 38
7 Operation.................................................................................................................................. 40
7.1 Pre-start procedure........................................................................................................... 40
7.2 Pre-startup inspections..................................................................................................... 40
7.3 Apply power....................................................................................................................... 41
7.4 Discharge time................................................................................................................... 41
8 Programming............................................................................................................................ 43
8.1 Display and control panel.................................................................................................43
8.2 Functions of push buttons................................................................................................ 43
8.3 Software parameters......................................................................................................... 44
8.3.1 M00 MAIN MENU....................................................................................................... 45
8.3.2 M20 STATUS................................................................................................................49
8.3.3 M40 DIAGNOSTICS....................................................................................................52
8.3.4 M60 SETTINGS............................................................................................................54
8.3.5 M100 BASIC SETTINGS..............................................................................................55
8.3.6 M200 CONF.INVERTER..............................................................................................57
8.3.7 M300 REGULATION................................................................................................... 69
8.3.8 M400 SENSOR............................................................................................................ 71
8.3.9 M500 SEQUENCE CONTR........................................................................................ 74
8.3.10 M600 ERROR.............................................................................................................78
8.3.11 M700 OUTPUTS........................................................................................................79
8.3.12 M800 REQUIRED VALUES....................................................................................... 81
8.3.13 M900 OFFSET........................................................................................................... 83
8.3.14 M1000 TEST RUN..................................................................................................... 86
8.3.15 M1100 SETUP........................................................................................................... 87
8.3.16 M1200 RS-485 INTERFACE..................................................................................... 89
8.3.17 M1300 START-UP..................................................................................................... 92
9 Maintenance..............................................................................................................................98
9.1 General................................................................................................................................98
9.2 Check error codes............................................................................................................. 98
9.3 Check the functions and parameters.............................................................................. 98
10 Troubleshooting.....................................................................................................................99
10.1 No error message on the display.................................................................................. 99
10.2 Error message on the display........................................................................................ 99
10.3 Internal error, on display or red LED ON................................................................... 101
11 Technical Reference............................................................................................................ 102
11.1 Example: P105 ACTUATOR mode..............................................................................102
Table of Contents
2 HVL 2.015-4.220 Installation, Operation, and Maintenance Manual

Table of Contents

Other manuals for Xylem hydrovar

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Xylem hydrovar and is the answer not in the manual?

Xylem hydrovar Specifications

General IconGeneral
Frequency50/60 Hz
Control typeVariable speed drive
Protection classIP55
Communication protocolsModbus
Relative Humidity5% - 95% (non-condensing)
AltitudeUp to 1000 m without derating
Input voltage200-690 V AC
Storage Temperature-25°C to +70°C (-13°F to 158°F)

Related product manuals