Yamaha F100D - Page 243

6D93G11
i-3
1
2
3
4
5
6
7
8
9
Index
H.
Hose routing................................................4-2
How to use this manual...............................1-1
I.
Identification................................................1-5
Ignition and ignition control system.............8-7
Installing the clamp brackets.....................7-21
Installing the cylinder head .......................5-34
Installing the drive shaft ............................6-20
Installing the exhaust cover ......................5-39
Installing the fuel hose clamp....................4-16
Installing the lower unit .............................6-22
Installing the power trim and tilt unit..........7-44
Installing the power unit ............................5-52
Installing the pressure control valve..........5-39
Installing the propeller shaft housing ........6-20
Installing the sprockets and timing belt .....5-18
Installing the steering arm.........................7-18
Installing the throttle position sensor...........4-9
Installing the upper case ...........................7-15
Installing the valves...................................5-33
Installing the water pump and shift rod .....6-21
Intake manifold............................................4-7
Introduction .................................................9-2
J.
Junction box..............................................5-22
L.
Lower unit ..................................2-6
,
3-12
,
6-4
Lubricating the outboard motor .................3-15
M.
Maintenance interval chart..........................3-2
Maintenance specification...........................2-3
Manual format .............................................1-1
Measuring the forward gear backlash.......6-28
Measuring the fuel pressure .....................4-13
Measuring the lower resistance ..................8-2
Measuring the peak voltage........................8-2
P.
Parts, lubricants, and sealants....................1-3
Port view .....................................................8-3
Power trim and tilt electrical system..........7-45
Power trim and tilt motor ...........................7-25
Power trim and tilt unit ..............................7-23
Power unit ............................ 2-3
,
3-4
,
5-3
,
9-5
Predelivery checks......................................1-6
Propeller selection ......................................1-5
Propeller shaft housing............................. 6-10
Propeller size.............................................. 1-5
R.
Reducing the fuel pressure....................... 4-13
Refacing the valve seat ............................ 5-30
Removing the clamp brackets .................. 7-21
Removing the cylinder head ..................... 5-26
Removing the drive shaft .......................... 6-17
Removing the exhaust cover .................... 5-39
Removing the fuel hose clamp ................. 4-16
Removing the lower unit ............................. 6-8
Removing the power trim and tilt unit ....... 7-24
Removing the power unit .......................... 5-16
Removing the propeller shaft housing
assembly ................................................ 6-11
Removing the steering arm ...................... 7-18
Removing the timing belt and sprockets... 5-17
Removing the upper case......................... 7-12
Removing the water pump and shift rod..... 6-9
Replacing the oil filter ................................. 3-5
Replacing the timing belt .......................... 5-13
Replacing the valve guides....................... 5-28
S.
Safety while working................................... 1-3
Selecting the connecting rod bearing ....... 5-46
Selecting the forward gear shims ............. 6-27
Selecting the main bearing ....................... 5-48
Selecting the pinion shims........................ 6-26
Selection..................................................... 1-6
Self-diagnosis ........................................... 9-18
Self-protection ............................................ 1-3
Serial number ............................................. 1-5
Shift rod ...................................................... 7-2
Shimming.........................................6-25
,
6-26
Special service
tools .............3-1
,
4-1
,
5-1
,
6-1
,
7-1
,
8-1
,
9-1
Specified torques...................................... 2-11
Starboard view............................................ 8-4
Starter motor............................................. 8-13
Starting system......................................... 8-11
Steering arm ............................................. 7-17
Symbols...................................................... 1-2
T.
Test run ...................................................... 1-9
Throttle link ............................................... 5-20
Tightening torques.................................... 2-11
Tilt cylinder and trim cylinder .................... 7-35
Top cowling ................................................ 3-3
Top view ..................................................... 8-6