DC Injection Braking Current..................155, 213
DC Injection Braking Time/DC Excitation Time at Start
.................................................. 213
Deceleration Time 1 ...........................93, 213
Deceleration Time 2 .............................. 213
Digital Operator Display Selection ................. 229
DIP Switch S1......................................62
Down Command ................................. 220
d References ..................................... 216
Drive/kVA Selection.............................. 230
Drive Baseblock .................................. 129
Drive Capacity Setting Fault....................... 145
Drive Capacity Signal Fault ...................128, 132
Drive Cooling Fans ............................... 165
Drive Dedicated Motor (Constant Torque, 1:10)..... 109
Drive Mode .................................79, 80, 81
Drive Overload ...............................128, 136
Drive Ready...................................... 222
Drive Slave Address .............................. 223
Drive Status Monitors............................. 110
Drive Transmit Wait Time......................... 224
Drive Unit Setting Error........................... 129
Drive Watt Loss Data ............................. 205
During Baseblock................................. 222
During Run ...................................... 221
Dynamic Braking Resistor......................... 128
E
E1-04 .............................. 146, 153, 154, 156
E1-04 through E1-10..................... 134, 135, 136
E1-06 ........................................135, 154
E1-07 ............................................ 146
E1-08 .............................. 125, 135, 136, 151
E1-09 ..........................146, 150, 151, 156, 157
E1-10 ..........................125, 135, 136, 151, 154
E1 V/f Pattern Characteristics...................... 218
E2-01 ..................... 108, 125, 135, 136, 218, 252
E2-02 ................................... 104, 125, 218
E2-03 ................................... 105, 125, 219
E2-05 ........................................105, 219
E2 Motor Parameters.............................. 218
EEPROM Data Error.............................. 131
EEPROM Write Error.........................128, 133
EF ...........................................129, 141
EF0..........................................128, 132
EF1..........................................132, 141
EF1 to EF5....................................... 129
EF2..........................................132, 142
EF3..........................................132, 142
EF4..........................................132, 142
EF5..........................................132, 142
Electrical Thermal Motor Protection ............... 107
EMC Guidelines.................................. 241
Err...........................................128, 133
Excessive Motor Oscillation and Erratic Rotation ... 155
External Digital Operator Connection Fault ......... 137
External Fault ................................133, 142
External Fault (input terminal S1 to S5) ........128, 129
External Fault (user selection possible) ............. 221
External Search Command 1....................... 221
External Search Command 2....................... 221
Drive Motor Overload Protection.................. 252
Drive Short-Circuit Rating ........................ 252
European Standards ................................16
Low Voltage Wiring ............................. 252
UL Standards ......................................16
F
Fast-stop (N.C.) .................................. 220
Fast-Stop (N.O.) .................................. 220
Fast-stop Time ................................... 213
Fault............................................. 222
Fault Causes and Solutions ........................ 130
Fault Detection ................................... 130
Fault Displays .................................... 130
Fault History Example ............................ 147
Fault Reset ....................................... 220
Fault Reset Example .............................. 127
Faults ........................................127, 128
FLASH memory error............................. 131
FLASH Memory Fault ............................ 128
Forward/Reverse Run Command Input Error........ 141
Forward Run Command (2-Wire sequence) ......... 221
Fref/Fout Agree 1................................. 221
Frequency (FOUT) Detection 1 .................... 221
Frequency (FOUT) Detection 2 .................... 222
Frequency Reference..........................110, 231
Frequency Reference 1 .........................97, 216
Frequency Reference 2 .........................97, 216
Frequency Reference 3 .........................97, 216
Frequency Reference 4 .........................97, 216
Index
YASKAWA ELECTRIC TOEP C710606 26B YASKAWA AC Drive – J1000 Quick Start Guide
257
To Next Page
Loading...
