3.9 F: Options
192 YASKAWA TOEPYAIGA8001B GA800 Drive Maintenance & Troubleshooting
No.
(Hex.)
Name Description
Default
(Range)
F6-61
(03DC)
DeviceNet Time Scaling
Sets the time scale of the DeviceNet communication master.
0
(-15 - +15)
F6-62
(03DD)
DeviceNet Heartbeat
Interval
Sets the heartbeat for DeviceNet communication. Set this parameter to 0 to disable the heartbeat
function.
0
(0 - 10)
F6-63
(03DE)
DeviceNet Network MAC
ID
Sets the function to see the actual DeviceNet MAC address using the keypad. This parameter
functions as a monitor only.
63
(0 - 63)
F6-64
(03DF)
Dynamic Out Assembly 109
Param1
Sets Configurable Output 1 written to the MEMOBUS register.
0000h
(0000h - FFFFh)
F6-65
(03E0)
Dynamic Out Assembly 109
Param2
Sets Configurable Output 2 written to the MEMOBUS register.
0000h
(0000h - FFFFh)
F6-66
(03E1)
Dynamic Out Assembly 109
Param3
Sets Configurable Output 3 written to the MEMOBUS register.
0000h
(0000h - FFFFh)
F6-67
(03E2)
Dynamic Out Assembly 109
Param4
Sets Configurable Output 4 written to the MEMOBUS register.
0000h
(0000h - FFFFh)
F6-68
(03E3)
Dynamic In Assembly 159
Param 1
Sets Configurable Input 1 read from the MEMOBUS register.
0000h
(0000h - FFFFh)
F6-69
(03E4)
Dynamic In Assembly 159
Param 2
Sets Configurable Input 2 read from the MEMOBUS register.
0000h
(0000h - FFFFh)
F6-70
(03C7)
Dynamic In Assembly 159
Param 3
Sets Configurable Input 3 read from the MEMOBUS register.
0000h
(0000h - FFFFh)
F6-71
(03C8)
Dynamic In Assembly 159
Param 4
Sets Configurable Input 4 read from the MEMOBUS register.
0000h
(0000h - FFFFh)
F6-72
(081B)
PowerLink Node Address
Sets the node ID for PowerLink communication.
Note:
Be sure to set an address that is different than all other node addresses. Do not set this parameter
to 0.
0
(0 - 255)
◆ F7: Communication Options
No.
(Hex.)
Name Description
Default
(Range)
F7-01
(03E5)
IP Address 1
Sets the first octet of the IP Address for the device that is connecting to the network. Restart the drive
after you change this parameter.
Note:
When F7-13 = 0 [Address Mode at Startup = Static]:
• Use parameters F7-01 to F7-04 [IP Address 1 to 4] to set the IP Address. Be sure to set a
different IP address for each drive on the network.
• Also set parameters F7-05 to F7-12 [Subnet Mask 1 to 4, Gateway Address 1 to 4].
192
(0 - 255)
F7-02
(03E6)
IP Address 2
Sets the second octet of the IP Address for the device that is connecting to the network. Restart the
drive after you change this parameter.
Note:
When F7-13 = 0 [Address Mode at Startup = Static]:
• Use parameters F7-01 to F7-04 [IP Address 1 to 4] to set the IP Address. Be sure to set a
different IP address for each drive on the network.
• Also set parameters F7-05 to F7-12 [Subnet Mask 1 to 4, Gateway Address 1 to 4].
168
(0 - 255)
F7-03
(03E7)
IP Address 3
Sets the third octet of the IP Address for the device that is connecting to the network. Restart the
drive after you change this parameter.
Note:
When F7-13 = 0 [Address Mode at Startup = Static]:
• Use parameters F7-01 to F7-04 [IP Address 1 to 4] to set the IP Address. Be sure to set a
different IP address for each drive on the network.
• Also set parameters F7-05 to F7-12 [Subnet Mask 1 to 4, Gateway Address 1 to 4].
1
(0 - 255)
To Next Page
Loading...
