YOKOGAWA DL9040

5-124
IM 701310-17E
:MEASure:THReshold?
Function Queries all settings related to the threshold levels
of the automated measurement of waveform
parameters.
Syntax
:MEASure:THReshold?
Example
:MEASURE:THRESHOLD? -> :MEASURE:
THRESHOLD:TRACE1:AUTO PTOPEAK;
LHYSTERESIS:HYSTERESIS 1.000E+00;
LEVEL 0.000E+00;:MEASURE:THRESHOLD:
TRACE1:MODE AUTO;ULOWER:
RANGE 2.000E+00,1.000E+00;:MEASURE:
THRESHOLD:TRACE2:AUTO PTOPEAK;
LHYSTERESIS:HYSTERESIS 1.000E+00;
LEVEL 0.000E+00;:MEASURE:THRESHOLD:
TRACE2:MODE AUTO;ULOWER:
RANGE 2.000E+00,1.000E+00;:MEASURE:
THRESHOLD:TRACE3:AUTO PTOPEAK;
LHYSTERESIS:HYSTERESIS 1.000E+00;
LEVEL 0.000E+00;:MEASURE:THRESHOLD:
TRACE3:MODE AUTO;ULOWER:
RANGE 2.000E+00,1.000E+00;:MEASURE:
THRESHOLD:TRACE4:AUTO PTOPEAK;
LHYSTERESIS:HYSTERESIS 1.000E+00;
LEVEL 0.000E+00;:MEASURE:THRESHOLD:
TRACE4:MODE AUTO;ULOWER:
RANGE 2.000E+00,1.000E+00;:MEASURE:
THRESHOLD:TRACE5:AUTO PTOPEAK;
LHYSTERESIS:HYSTERESIS 1.000E+00;
LEVEL 0.000E+00;:MEASURE:THRESHOLD:
TRACE5:MODE AUTO;ULOWER:
RANGE 2.000E+00,1.000E+00;:MEASURE:
THRESHOLD:TRACE6:AUTO PTOPEAK;
LHYSTERESIS:HYSTERESIS 1.000E+00;
LEVEL 0.000E+00;:MEASURE:THRESHOLD:
TRACE6:MODE AUTO;ULOWER:RANGE ......
Description This command is valid when the <Parameter> of
:MEASure:TRACe<x>:AREA<x>:<Parameter>
is
not RISE or FALL.
:MEASure:THReshold:TRACe<x>?
Function Queries the threshold levels of the trace.
Syntax
:MEASure:THReshold:TRACe<x>?
<x> = 1 to 8
Example
:MEASURE:THRESHOLD:TRACE1? -> :MEASURE:
THRESHOLD:TRACE1:AUTO PTOPEAK;
LHYSTERESIS:HYSTERESIS 1.000E+00;
LEVEL 0.000E+00;:MEASURE:THRESHOLD:
TRACE1:MODE AUTO;ULOWER:
RANGE 1.000E+00,2.000E+00
Description This command is valid when the <Parameter> of
:MEASure:TRACe<x>:AREA<x>:<Parameter>
is
not RISE or FALL.
:MEASure:THReshold:TRACe<x>:AUTO
Function Sets the detection mode when the auto setting of
the threshold level is enabled or queries the current
setting.
Syntax
:MEASure:THReshold:TRACe<x>:AUTO {HLOW|
PTOPeak}
:MEASure:THReshold:TRACe<x>:AUTO?
<x> = 1 to 8
Example
:MEASURE:THRESHOLD:TRACE1:AUTO PTOPEAK
:MEASURE:THRESHOLD:TRACE1:AUTO?
-> :MEASURE:THRESHOLD:TRACE1:
AUTO PTOPEAK
Description This command is valid when the <Parameter> of
:MEASure:TRACe<x>:AREA<x>:<Parameter>
is
not RISE or FALL.
:MEASure:THReshold:TRACe<x>:
LHYSteresis?
Function Queries all settings related to the level and hysteresis
of the threshold level.
Syntax
:MEASure:THReshold:TRACe<x>:
LHYSteresis?
<x> = 1 to 8
Example
:MEASURE:THRESHOLD:TRACE1:LHYSTERESIS?
-> :MEASURE:THRESHOLD:TRACE1:
LHYSTERESIS:HYSTERESIS 1.000E+00;
LEVEL 0.000E+00
Description This command is valid when the <Parameter> of
:MEASure:TRACe<x>:AREA<x>:<Parameter>
is
not RISE or FALL.
:MEASure:THReshold:TRACe<x>:
LHYSteresis:HYSTeresis
Function Sets the hysteresis of the threshold level or queries
the current setting.
Syntax
:MEASure:THReshold:TRACe<x>:
LHYSteresis:HYSTeresis {<NRf>}
:MEASure:THReshold:TRACe<x>:
LHYSteresis:HYSTeresis?
<x> = 1 to 8
<NRf> = 0 to 4 (div)
Example
:MEASURE:THRESHOLD:TRACE1:LHYSTERESIS:
HYSTERESIS 1
:MEASURE:THRESHOLD:TRACE1:LHYSTERESIS:
HYSTERESIS? -> :MEASURE:THRESHOLD:
TRACE1:
LHYSTERESIS:HYSTERESIS 1.000E+00
Description This command is valid when the <Parameter> of
:MEASure:TRACe<x>:AREA<x>:<Parameter>
is
not RISE or FALL.
5.18 MEASure Group