YOKOGAWA DL9040

5-125
IM 701310-17E
Commands
1
2
3
4
5
6
App
Index
:MEASure:THReshold:TRACe<x>:
LHYSteresis:LEVel
Function Sets the level of the threshold level or queries the
current setting.
Syntax
:MEASure:THReshold:TRACe<x>:
LHYSteresis:LEVel {<NRf>|<Voltage>|<Cur
rent>}
:MEASure:THReshold:TRACe<x>:
LHYSteresis:LEVel?
<x> = 1 to 8
<NRf>, <V
oltage>, and <Current> = See the DL9000
User’s Manual.
Example
:MEASURE:THRESHOLD:TRACE1:LHYSTERESIS:
LEVEL 1
:MEASURE:THRESHOLD:TRACE1:LHYSTERESIS:
LEVEL? -> :MEASURE:THRESHOLD:TRACE1:
LHYSTERESIS:LEVEL 1.000E+00
Description This command is valid when the <Parameter> of
:MEASure:TRACe<x>:AREA<x>:<Parameter>
is
not RISE or FALL.
:MEASure:THReshold:TRACe<x>:MODE
Function Sets the setup mode of the threshold level or queries
the current setting.
Syntax
:MEASure:THReshold:TRACe<x>:MODE {AUTO|
LHYSteresis|ULOWer}
:MEASure:THReshold:TRACe<x>:MODE?
<x> = 1 to 8
Example
:MEASURE:THRESHOLD:TRACE1:
MODE LHYSTERESIS
:MEASURE:THRESHOLD:TRACE1:MODE?
-> :MEASURE:THRESHOLD:TRACE1:
MODE LHYSTERESIS
Description This command is valid when the <Parameter> of
:MEASure:TRACe<x>:AREA<x>:<Parameter>
is
not RISE or FALL.
:MEASure:THReshold:TRACe<x>:ULOWer?
Function Queries all settings related to the upper and lower
limits of the threshold level.
Syntax
:MEASure:THReshold:TRACe<x>:ULOWer?
<x> = 1 to 8
Example
:MEASURE:THRESHOLD:TRACE1:ULOWER?
-> :MEASURE:THRESHOLD:TRACE1:ULOWER:
RANGE 2.000E+00,1.000E+00
Description This command is valid when the <Parameter> of
:MEASure:TRACe<x>:AREA<x>:<Parameter>
is
not RISE or FALL.
:MEASure:THReshold:TRACe<x>:ULOWer:
RANGe
Function Sets the upper and lower limits of the threshold level
or queries the current setting.
Syntax
:MEASure:THReshold:TRACe<x>:ULOWer:
RANGe {(<NRf>,<NRf>)|
(<Voltage>,<Voltage>)|
(<Current>,<Current>)}
:MEASure:THReshold:TRACe<x>:ULOWer:
RANGe?
<x> = 1 to 8
<NRf>, <V
oltage>, and <Current> = See the DL9000
User’s Manual.
Example
:MEASURE:THRESHOLD:TRACE1:ULOWER:
RANGE 1,2
:MEASURE:THRESHOLD:TRACE1:ULOWER:RANGE?
-> :MEASURE:THRESHOLD:TRACE1:ULOWER:
RANGE 2.000E+00,1.000E+00
Description This command is valid when the <Parameter> of
:MEASure:TRACe<x>:AREA<x>:<Parameter>
is
not RISE or FALL.
5.18 MEASure Group