YOKOGAWA DL9040 - Page 203

5-169
IM 701310-17E
Commands
1
2
3
4
5
6
App
Index
:TRIGger:EINTerval:EVENt<x>:LINBus:
SOURce
Function Sets the LIN bus signal trigger source or queries the
current setting.
Syntax
:TRIGger:EINTerval:EVENt<x>:LINBus:
SOURce {<NRf>}
:TRIGger:EINTerval:EVENt<x>:LINBus:
SOURce?
<x> = 1 or 2
<NRf> = 1 to 4
Example
:TRIGGER:EINTERVAL:EVENT1:LINBUS:
SOURCE 1
:TRIGGER:EINTERVAL:EVENT1:LINBUS:
SOURCE? -> :TRIGGER:EINTERVAL:EVENT1:
LINBUS:SOURCE 1
:TRIGger:EINTerval:EVENt<x>:SPATtern?
(Serial Pattern)
Function Queries all settings related to the serial pattern trigger
of the event.
Syntax
:TRIGger:EINTerval:EVENt<x>:SPATtern?
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:SPATTERN?
-> :TRIGGER:EINTERVAL:EVENT1:SPATTERN:
BITRATE 1.000E+00;CLOCK:MODE 1;
POLARITY FALL;SOURCE 1;:TRIGGER:
EINTERVAL:EVENT1:SPATTERN:CS 1;DATA:
ACTIVE HIGH;SOURCE 1;:TRIGGER:
EINTERVAL:EVENT1:SPATTERN:LATCH:
SOURCE 1;POLARITY FALL;:TRIGGER:
EINTERVAL:EVENT1:SPATTERN:
PATTERN "1100110111101111"
:TRIGger:EINTerval:EVENt<x>:SPATtern:
BITRate
Function Sets the bit rate of the serial pattern trigger or queries
the current setting.
Syntax
:TRIGger:EINTerval:EVENt<x>:SPATtern:
BITRate {<NRf>}
:TRIGger:EINTerval:EVENt<x>:SPATtern:
BITRate?
<x> = 1 or 2
<NRf> = 1 to 50M (bps)
Example
:TRIGGER:EINTERVAL:EVENT1:SPATTERN:
BITRATE 1
:TRIGGER:EINTERVAL:EVENT1:SPATTERN:
BITRATE? -> :TRIGGER:EINTERVAL:EVENT1:
SPATTERN:BITRATE 1.000E+00
Description This command is valid when
:TRIGger:
EINTerval:EVENt<x>:SPATtern:CLOCk:
MODE OFF
.
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLEar
Function Clears the entire pattern of the serial pattern trigger (to
don’t care).
Syntax
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLEar
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:SPATTERN:
CLEAR
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLOCk?
Function Queries all settings related to clock of the serial
pattern trigger.
Syntax
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLOCk?
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:SPATTERN:
CLOCK? -> :TRIGGER:EINTERVAL:EVENT1:
SPATTERN:CLOCK:MODE 1;POLARITY FALL;
SOURCE 1
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLOCk:MODE
Function Enables/Disables the clock of the serial pattern
trigger or queries the current setting.
Syntax
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLOCk:MODE {<Boolean>}
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLOCk:MODE?
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:SPATTERN:
CLOCK:MODE ON
:TRIGGER:EINTERVAL:EVENT1:SPATTERN:
CLOCK:MODE? -> :TRIGGER:EINTERVAL:
EVENT1:SPATTERN:CLOCK:MODE 1
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLOCk:POLarity
Function Sets the polarity of the clock trace of the serial pattern
trigger or queries the current setting.
Syntax
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLOCk:POLarity {FALL|RISE}
:TRIGger:EINTerval:EVENt<x>:SPATtern:
CLOCk:POLarity?
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:SPATTERN:
CLOCK:POLARITY FALL
:TRIGGER:EINTERVAL:EVENT1:SPATTERN:
CLOCK:POLARITY? -> :TRIGGER:EINTERVAL:
EVENT1:SPATTERN:CLOCK:POLARITY FALL
Description This command is valid when
:TRIGger:
EINTerval:EVENt<x>:SPATtern:CLOCk:
MODE ON
.
5.29 TRIGger Group