YOKOGAWA DL9040

5-174
IM 701310-17E
:TRIGger:EINTerval:EVENt<x>:SPIBus:
MODE
Function Sets the wiring system of the SPI bus trigger (three-
wire or four-wire) or queries the current setting.
Syntax
:TRIGger:EINTerval:EVENt<x>:SPIBus:
MODE {WIRE3|WIRE4}
:TRIGger:EINTerval:EVENt<x>:SPIBus:
MODE?
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:SPIBUS:
MODE WIRE3
:TRIGGER:EINTERVAL:EVENT1:SPIBUS:MODE?
-> :TRIGGER:EINTERVAL:EVENT1:SPIBUS:
MODE WIRE3
:TRIGger:EINTerval:EVENt<x>:STATe?
Function Queries all settings related to condition to be satisfied
of the event.
Syntax
:TRIGger:EINTerval:EVENt<x>:STATe?
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:STATE? -> :
TRIGGER:EINTERVAL:EVENT1:STATE:
CHANNEL1 DONTCARE;CHANNEL2 DONTCARE;
CHANNEL3 DONTCARE;CHANNEL4 DONTCARE;
LOGIC AND
:TRIGger:EINTerval:EVENt<x>:STATe:
CHANnel<x>
Function Sets the condition to be satisfied of the channel or
queries the current setting.
Syntax
:TRIGger:EINTerval:EVENt<x>:STATe:
CHANnel<x> {DONTcare|HIGH|IN|LOW|OUT}
:TRIGger:EINTerval:EVENt<x>:STATe:
CHANnel<x>?
<x> of EVENt<x> = 1 or 2
<x> of CHANnel<x> = 1 to 4
Example
:TRIGGER:EINTERVAL:EVENT1:STATE:
CHANNEL1 HIGH
:TRIGGER:EINTERVAL:EVENT1:STATE:
CHANNEL1? -> :TRIGGER:EINTERVAL:EVENT1:
STATE:CHANNEL1 HIGH
Description • This command is valid when
:TRIGger:
EINTerval:EVENt<x>:TYPE EQUalify|I2CB
us|PQUalify|PSTAte|SPATtern|STATe
.
• {HIGH|LOW} is valid when
:TRIGger:
EINTerval:EVENt<x>:TYPE I2CBus|
SPATtern
.
• {IN|OUT} is valid when
:TRIGger:EINTerval:
EVENt<x>:TYPE EQUalify|PQUalify|PSTAt
e|STATe
and
TRIGger:SOURce:CHANnel<x>:
WINDow ON
. {HIGH|LOW} is valid when
:
TRIGger:EINTerval:EVENt<x>:TYPE EQUal
ify|PQUalify|PSTAte|STATe
and
TRIGger:
SOURce:CHANnel<x>:WINDow OFF
.
:TRIGger:EINTerval:EVENt<x>:STATe:
LOGic
Function Sets the logic of the condition to be satisfied or
queries the current setting.
Syntax
:TRIGger:EINTerval:EVENt<x>:STATe:
LOGic {AND|OR}
:TRIGger:EINTerval:EVENt<x>:STATe:
LOGic?
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:STATE:
LOGIC AND
:TRIGGER:EINTERVAL:EVENT1:STATE:LOGIC?
-> :TRIGGER:EINTERVAL:EVENT1:STATE:
LOGIC AND
Description This command is valid when
:TRIGger:
EINTerval:EVENt<x>:TYPE EQUalify|
I2CBus|PQUalify|PSTAte|SPATtern|STATe
.
:TRIGger:EINTerval:EVENt<x>:TYPE
Function Sets the trigger type of the event or queries the
current setting.
Syntax
:TRIGger:EINTerval:EVENt<x>:
TYPE {CANBus|EDGE|EQUalify|I2CBus|
LINBus|PQUalify|PSTAte|PULSe|SPATtern|
SPIBus|STATe}
:TRIGger:EINTerval:EVENt<x>:TYPE?
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:TYPE CANBUS
:TRIGGER:EINTERVAL:EVENT1:TYPE?
-> :TRIGGER:EINTERVAL:EVENT1:
TYPE CANBUS
:TRIGger:EINTerval:EVENt<x>:WIDTh?
Function Queries all settings related to the pulse width trigger
of the event.
Syntax
:TRIGger:EINTerval:EVENt<x>:WIDTh?
<x> = 1 or 2
Example
:TRIGGER:EINTERVAL:EVENT1:WIDTH?
-> :TRIGGER:EINTERVAL:EVENT1:WIDTH:
MODE TIMEOUT;POLARITY POSITIVE;
SOURCE EXTERNAL;TIME1 1.000E+00;
TIME2 1.000E+00
5.29 TRIGger Group