YOKOGAWA DL9040

5-198
IM 701310-17E
:TRIGger:SOURce:CHANnel<x>:STATe
Function Sets the condition to be satisfied of the channel or
queries the current setting.
Syntax
:TRIGger:SOURce:CHANnel<x>:
STATe {DONTcare|HIGH|IN|LOW|OUT}
:TRIGger:SOURce:CHANnel<x>:STATe?
<x> = 1 to 4
Example
:TRIGGER:SOURCE:CHANNEL1:STATE HIGH
:TRIGGER:SOURCE:CHANNEL1:STATE?
-> :TRIGGER:SOURCE:CHANNEL1:STATE HIGH
Description • This command is valid when
:TRIGger:TYPE
EQUalify|I2CBus|PQUalify|PSTAte|
SPATtern|STATe
.
• {HIGH|LOW} is valid when
:TRIGger:TYPE
I2CBus|SPATtern
.
• {IN|OUT} is valid when
:TRIGger:TYPE EQUali
fy|PQUalify|PSTAte|STATe
and
:TRIGger:
SOU
Rce:CHANnel<x>:WINDow ON
. {HIGH|LOW}
is valid when
:TRIGger:TYPE EQUalify|PQUa
lify|PSTAte|STATe
and
:TRIGger:SOURce:
CHANnel<x>:WINDow OFF
.
:TRIGger:SOURce:CHANnel<x>:WIDTh
Function Sets the window trigger width of the channel or
queries the current setting.
Syntax
:TRIGger:SOURce:CHANnel<x>:
WIDTh {<Voltage>|<Current>}
:TRIGger:SOURce:CHANnel<x>:WIDTh?
<x> = 1 to 4
<V
oltage> and <Current> = See the DL9000 User’s
Manual.
Example
:TRIGGER:SOURCE:CHANNEL1:WIDTH 1V
:TRIGGER:SOURCE:CHANNEL1:WIDTH?
-> :TRIGGER:SOURCE:CHANNEL1:
WIDTH 1.000E+00
Description This command is valid when :TRIGger:SOURce:
CHANnel<x>:WINDow ON.
:TRIGger:SOURce:CHANnel<x>:WINDow
Function Turns ON/OFF the window of the channel or queries
the current setting.
Syntax
:TRIGger:SOURce:CHANnel<x>:
WINDow {<Boolean>}
:TRIGger:SOURce:CHANnel<x>:WINDow?
<x> = 1 to 4
Example
:TRIGGER:SOURCE:CHANNEL1:WINDOW ON
:TRIGGER:SOURCE:CHANNEL1:WINDOW?
-> :TRIGGER:SOURCE:CHANNEL1:WINDOW 1
:TRIGger:SOURce:EXTernal?
Function Queries all settings related to the external trigger.
Syntax
:TRIGger:SOURce:EXTernal?
Example
:TRIGGER:SOURCE:EXTERNAL? -> :TRIGGER:
SOURCE:EXTERNAL:LEVEL 0.000E+00;PROBE 1
:TRIGger:SOURce:EXTernal:LEVel
Function Sets the trigger level of the external trigger or queries
the current setting.
Syntax
:TRIGger:SOURce:EXTernal:
LEVel {<Voltage>|<Current>}
:TRIGger:SOURce:EXTernal:LEVel?
<x> = 1 to 4
<V
oltage> and <Current> = See the DL9000 User’s
Manual.
Example
:TRIGGER:SOURCE:EXTERNAL:LEVEL 1V
:TRIGGER:SOURCE:EXTERNAL:LEVEL?
-> :TRIGGER:SOURCE:EXTERNAL:
LEVEL 1.000E+00
Description This command is valid when :TRIGger:TYPE EDGE|
EQUalify|PQUalify|PULSe.
:TRIGger:SOURce:EXTernal:PROBe
Function Sets the probe attenuation of the external trigger or
queries the current setting.
Syntax
:TRIGger:SOURce:EXTernal:PROBe {<NRf>}
:TRIGger:SOURce:EXTernal:PROBe?
<NRf> = 1,10
Example
:TRIGGER:SOURCE:EXTERNAL:PROBE 1
:TRIGGER:SOURCE:EXTERNAL:PROBE?
-> :TRIGGER:SOURCE:EXTERNAL:PROBE 1
Description This command is valid when
:TRIGger:
TYPE EDGE|EQUalify|PQUalify|PULSe
.
:TRIGger:SOURce:LOGic
Function Sets the trigger source logic or queries the current
setting.
Syntax
:TRIGger:SOURce:LOGic {AND|OR}
:TRIGger:SOURce:LOGic?
Example
:TRIGGER:SOURCE:LOGIC AND
:TRIGGER:SOURCE:LOGIC? -> :TRIGGER:
SOURCE:LOGIC AND
Description This command is valid when
:TRIGger:
TYPE EQUalify|I2CBus|PQUalify|PSTAte|
SPATtern|STATe
.
:TRIGger:TYPE
Function Sets the trigger type or queries the current setting.
Syntax
:TRIGger:TYPE {CANBus|EDGE|EICYcle|
EIDelay|EISequence|EOR|EQUalify|
I2CBus|LEDGe|LINBus|PQUalify|PSTAte|
PULSe|SPATtern|SPIBus|STATe|TV|UART}
:TRIGger:TYPE?
Example
:TRIGGER:TYPE CANBUS:TRIGGER:TYPE?
-> :TRIGGER:TYPE CANBUS
:TRIGger:WIDTh?
Function Queries all settings related to the pulse width trigger.
Syntax
:TRIGger:WIDTh?
Example
:TRIGGER:WIDTH? -> :TRIGGER:WIDTH:
MODE OUT;POLARITY POSITIVE;SOURCE 1;
TIME1 1.000E-09;TIME2 1.000E-09
5.29 TRIGger Group