YOKOGAWA DL9040

5-40
IM 701310-17E
:ANALysis:AHIStogram<x>:MEASure:
PARameter:AREA<x>?
Function Queries all settings related to the area of the
accumulated histogram.
Syntax
:ANALysis:AHIStogram<x>:MEASure:
PARameter:AREA<x>?
<x> of
AHIStogram<x> = 1 or 2
<x> of AREA<x> = 1 or 2
Example
:ANALYSIS:AHISTOGRAM1:MEASURE:
PARAMETER:AREA1? -> :ANALYSIS:
AHISTOGRAM1:MEASURE:
PARAMETER:AREA1:MAXIMUM:STATE 1;:
ANALYSIS:AHISTOGRAM1:MEASURE:PARAMETER:
AREA1:MEAN:STATE 1;:ANALYSIS:
AHISTOGRAM1:MEASURE:PARAMETER:AREA1:
MEDIAN:STATE 1;:ANALYSIS:AHISTOGRAM1:
MEASURE:PARAMETER:AREA1:MINIMUM:
STATE 1;:ANALYSIS:AHISTOGRAM1:MEASURE:
PARAMETER:AREA1:PEAK:STATE 1;:ANALYSIS:
AHISTOGRAM1:MEASURE:PARAMETER:AREA1:
RMS:STATE 1;:ANALYSIS:AHISTOGRAM1:
MEASURE:PARAMETER:AREA1:SD2INTEG:
STATE 1;:ANALYSIS:AHISTOGRAM1:MEASURE:
PARAMETER:AREA1:SD3INTEG:STATE 1;:
ANALYSIS:AHISTOGRAM1:MEASURE:PARAMETER:
AREA1:SDEVIATION:STATE 1;:ANALYSIS:
AHISTOGRAM1:MEASURE:PARAMETER:AREA1:
SDINTEG:STATE 1
:ANALysis:AHIStogram<x>:MEASure:
PARameter:AREA<x>:ALL
Function Turns ON/OFF all waveform parameters of the
accumulated histogram.
Syntax
:ANALysis:AHIStogram<x>:MEASure:
PARameter:AREA<x>:ALL {<Boolean>}
<x> of
AHIStogram<x> = 1 or 2
<x> of AREA<x> = 1 or 2
Example
:ANALYSIS:AHISTOGRAM1:MEASURE:
PARAMETER:AREA1:ALL ON
:ANALysis:AHIStogram<x>:MEASure:
PARameter:AREA<x>:<Parameter>?
Function Queries all settings related to the waveform
parameter of the accumulated histogram.
Syntax
:ANALysis:AHIStogram<x>:MEASure:
PARameter:AREA<x>:<Parameter>?
<x> of
AHIStogram<x> = 1 or 2
<x> of AREA<x> = 1 or 2
<Parameter> = {MAXimum|MEAN|MEDian|
MINimum|PEAK|RMS|SD2integ|SD3integ|
SDEViation|SDINteg}
Example
(The following is an example for the maximum value
of area 1.)
:ANALYSIS:AHISTOGRAM1:MEASURE:
PARAMETER:AREA1:MAXIMUM? -> :ANALYSIS:
AHISTOGRAM1:MEASURE:
PARAMETER:AREA1:MAXIMUM:STATE 1
:ANALysis:AHIStogram<x>:MEASure:
PARameter:AREA<x>:<Parameter>:STATe
Function Turns ON/OFF the waveform parameter of the
accumulated histogram or queries the current setting.
Syntax
:ANALysis:AHIStogram<x>:MEASure:
PARameter:AREA<x>:<Parameter>:
STATe {<Boolean>}
:ANALysis:AHIStogram<x>:MEASure:
PARameter:AREA<x>:<Parameter>:STATe?
<x> of
AHIStogram<x> = 1 or 2
<x> of AREA<x> = 1 or 2
<Parameter> = {MAXimum|MEAN|MEDian|
MINimum|PEAK|RMS|SD2integ|SD3integ|
SDEViation|SDINteg}
Example
(The following is an example for the maximum value
of area 1.)
:ANALYSIS:AHISTOGRAM1:MEASURE:
PARAMETER:AREA1:MAXIMUM:STATE ON
:ANALYSIS:AHISTOGRAM1:MEASURE:
PARAMETER:AREA1:MAXIMUM:STATE?
-> :ANALYSIS:AHISTOGRAM1:MEASURE:
PARAMETER:AREA1:MAXIMUM:STATE 1
5.3 ANALysis Group