5-101
IM 710105-17E
Commands
5
:FILE[:DIRectory]:PATH?
Function Queries the current directory.
Syntax
:FILE[:DIRectory]:PATH?
Example
:FILE:DIRECTORY:PATH?
-> :FILE:DIRECTORY:PATH "PATH =
FLASHMEM/UTIL"
:FILE:LOAD:BINary:ABORt
Function Aborts the loading of waveform data.
Syntax
:FILE:LOAD:BINary:ABORt
Example
:FILE:LOAD:BINARY:ABORT
:FILE:LOAD:BINary[:EXECute]
Function Loads waveform data. This is an overlap
command.
Syntax
:FILE:LOAD:BINary[
:EXECute] {<File name>{,ACQMemory|
REFerence<x>}}
<x> = 1 or 2
Example
:FILE:LOAD:BINARY:EXECUTE "DATA"
:FILE:LOAD:{SETup|SNAP|ZPOLygon<x>|Z
WAVe<x>}:ABORt
Function Aborts the loading of a specific type of data.
Syntax
:FILE:LOAD:{SETup|SNAP|ZPOLygon<x>|
ZWAVe<x>}:ABORt
<x> = 1 to 4
Example (Below is an example for setup data.)
:FILE:LOAD:SETUP:ABORT
:FILE:LOAD:{SETup|SNAP|ZPOLygon<x>|Z
WAVe<x>}[:EXECute]
Function Loads a specific type of data. This is an overlap
command.
Syntax
:FILE:LOAD:{SETup|SNAP|ZPOLygon<x>|
ZWAVe<x>}[:EXECute] {<File name>}
<x> = 1 to 4
Example (Below is an example for setup data.)
:FILE:LOAD:SETUP:EXECUTE "DATA"
:FILE:MOVE:ABORt
Function Aborts file moving.
Syntax
:FILE:MOVE:ABORt
Example
:FILE:MOVE:ABORT
:FILE:MOVE:CDIRectory
Function Changes the file move destination directory.
Syntax
:FILE:MOVE:CDIRectory {<String>}
<String> = See the DLM2000 Features Guide for
this information.
Example
:FILE:MOVE:CDIRECTORY "UTIL"
:FILE:MOVE:DRIVe
Function Sets the file move destination medium.
Syntax
:FILE:MOVE:DRIVe {FLAShmem|USB,<NRf>}
<NRf> = 0 to 3
Example
:FILE:MOVE:DRIVE FLASHMEM
Description You can omit the <NRf> for USB if the drive is not
partitioned or is not divided into LUNs.
:FILE:MOVE[:EXECute]
Function Executes file moving. This is an overlap command.
Syntax
:FILE:MOVE[:EXECute] {<String>}
<String> = See the DLM2000 Features Guide for
this information.
Example
:FILE:MOVE:EXECUTE "DATA.PNG"
:FILE:MOVE:PATH?
Function Queries the file move destination directory.
Syntax
:FILE:MOVE:PATH?
Example
:FILE:MOVE:PATH?
-> :FILE:MOVE:PATH "PATH = FLASHMEM/
UTIL"
:FILE:PROTect[:EXECute]
Function Turns file protection on or off.
Syntax
:FILE:PROTect[:EXECute] {<String>,
<Boolean>}
<String> = See the DLM2000 Features Guide for
this information.
Example
:FILE:PROTECT:EXECUTE "DATA.PNG",ON
:FILE:REName[:EXECute]
Function Renames a file.
Syntax
:FILE:REName[:EXECute] {<String>,
<String>}
<String> = See the DLM2000 Features Guide for
this information.
Example
:FILE:RENAME:EXECUTE "DATA.PNG",
"000.PNG"
:FILE:SAVE?
Function Queries all file save settings.
Syntax
:FILE:SAVE?
:FILE:SAVE:{AHIStogram|ASCii|BINary|
FFT|HLISt|HARMonics|SBUS|ZWAVe}?
Function Queries all of the settings related to the saving of
a specified type of file.
Syntax
:FILE:SAVE:{AHIStogram|ASCii|BINary|F
FT|HLISt|HARMonics|SBUS|ZWAVe}?
5.12 FILE Group
To Next Page
General
