YOKOGAWA DLM2000 Series User Manual

5-130
IM 710105-17E
:MEASure:BIT<x>:AREA2:DELay:REFerenc
e:COUNt
Function Sets or queries the edge count of the reference
waveform used to measure the delay between
the specified logic waveform and the reference
waveform in Area2.
Syntax
:MEASure:BIT<x>:AREA2:DELay:
REFerence:COUNt {<NRf>}
:MEASure:BIT<x>:AREA2:DELay:
REFerence:COUNt?
<x> = 1 to 8
<NRf> = 1 to 10
Example
:MEASURE:BIT1:AREA2:DELAY:REFERENCE:C
OUNT 2
:MEASURE:BIT1:AREA2:DELAY:REFERENCE:C
OUNT?
-> :MEASURE:BIT1:AREA2:DELAY:REFERENC
E:COUNT 2
:MEASure:BIT<x>:AREA2:DELay:REFerenc
e:SLOPe
Function Sets or queries the slope of the reference waveform
used to measure the delay between the specified
logic waveform and the reference waveform in
Area2.
Syntax
:MEASure:BIT<x>:AREA2:DELay:
REFerence:SLOPe {FALL|RISE}
:MEASure:BIT<x>:AREA2:DELay:
REFerence:SLOPe?
<x> = 1 to 8
Example
:MEASURE:BIT1:AREA2:DELAY:REFERENCE:S
LOPE FALL
:MEASURE:BIT1:AREA2:DELAY:REFERENCE:S
LOPE?
-> :MEASURE:BIT1:AREA2:DELAY:REFERENC
E:SLOPE FALL
:MEASure:BIT<x>:AREA2:DELay:REFerenc
e:SOURce
Function Sets or queries whether the reference point for
measuring the delay between channels of a logic
waveform of Area2 will be set to the trigger point
or a waveform.
Syntax
:MEASure:BIT<x>:AREA2:DELay:
REFerence:SOURce {TRACe|TRIGger}
:MEASure:BIT<x>:AREA2:DELay:
REFerence:SOURce?
<x> = 1 to 8
Example
:MEASURE:BIT1:AREA2:DELAY:REFERENCE:S
OURCE TRACE
:MEASURE:BIT1:AREA2:DELAY:REFERENCE:S
OURCE?
-> :MEASURE:BIT1:AREA2:DELAY:REFERENC
E:SOURCE TRACE
:MEASure:BIT<x>:AREA2:DELay:REFerenc
e:TRACe
Function Sets or queries the reference waveform edge used
to measure the delay between the specified logic
waveform and the reference waveform in Area2.
Syntax
:MEASure:BIT<x>:AREA2:DELay:
REFerence:TRACe {<NRf>|BIT<x>|
MATH<x>}
:MEASure:BIT<x>:AREA2:DELay:
REFerence:TRACe?
<x> of BIT<x> = 1 to 8
<NRf> = 1 to 4 (1 or 2 for 2-channel models)
<x> of MATH<x> = 1 or 2 (1 only for 2-channel
models)
Example
:MEASURE:BIT1:AREA2:DELAY:REFERENCE:T
RACE 2
:MEASURE:BIT1:AREA2:DELAY:REFERENCE:T
RACE?
-> :MEASURE:BIT1:AREA2:DELAY:REFERENC
E:TRACE 2
:MEASure:BIT<x>:AREA2:DELay:STATe
Function Sets or queries the on/off status and the display
format of a delay parameter in Area2.
Syntax
:MEASure:BIT<x>:AREA2:DELay:STATe {OF
F|ON|DEGRee}
:MEASure:BIT<x>:AREA2:DELay:STATe?
<x> = 1 to 8
Example
:MEASURE:BIT1:AREA2:DELAY:STATE ON
:MEASURE:BIT1:AREA2:DELAY:STATE?
-> :MEASURE:BIT1:AREA2:DELAY:STATE ON
:MEASure:BIT<x>:<Parameter>?
Function Queries the setting of a waveform parameter of a
logic waveform.
Syntax
:MEASure:BIT<x>:<Parameter>?
<x> = 1 to 8
<Parameter> = {
AVGFreq|DELay|DUTYcycle|
FREQuency|PERiod|PNUMber
}
:MEASure:BIT<x>:<Parameter>:COUNt?
Function Queries the statistical processing count of a logic
waveform parameter.
Syntax
:MEASure:BIT<x>:<Parameter>:COUNt?
<x> = 1 to 8
<Parameter> = {
AVGFreq|DELay|DUTYcycle|
FREQuency|PERiod|PNUMber
}
Example (Below is an example for the average frequency of
bit 1.)
:MEASURE:BIT1:AVGFREQ:COUNT?
-> :MEASURE:BIT1:AVGFREQ:COUNT 100
5.20 MEASure Group

YOKOGAWA DLM2000 Series Specifications

General

Brand	YOKOGAWA
Model	DLM2000 Series
Category	Test Equipment
Language	English