YOKOGAWA DLM2000 Series - Page 247

5-214
IM 710105-17E
:SERialbus<x>:SPI[:ANALyze]:SETup:CL
OCk:SOURce
Function Sets or queries the clock signal for SPI bus signal
analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:CLO
Ck:SOURce {<NRf>|BIT<x>|MATH<x>}
:SERialbus<x>:SPI[:ANALyze]:SETup:CLO
Ck:SOURce?
<x> = 1 to 4
<NRf> = 1 to 4
<x> of BIT<x> = 1 to 8
<x> of MATH<x> = 1 or 2
Example
:SERIALBUS1:SPI:ANALYZE:SETUP:CLOCK:S
OURCE 1
:SERIALBUS1:SPI:ANALYZE:SETUP:CLOCK:S
OURCE?
-> :SERIALBUS1:SPI:ANALYZE:SETUP:CLOC
K:SOURCE 1
:SERialbus<x>:SPI[:ANALyze]:SETup:
CS?
Function Queries all chip select signal settings for SPI bus
signal analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:CS?
<x> = 1 to 4
:SERialbus<x>:SPI[:ANALyze]:SETup:CS
:ACTive
Function Sets or queries the chip select signal active state
for SPI bus signal analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:CS:
ACTive {HIGH|LOW}
:SERialbus<x>:SPI[:ANALyze]:SETup:CS:
ACTive?
<x> = 1 to 4
Example
:SERIALBUS1:SPI:ANALYZE:SETUP:CS:ACTI
VE HIGH
:SERIALBUS1:SPI:ANALYZE:SETUP:CS:ACTI
VE?
-> :SERIALBUS1:SPI:ANALYZE:SETUP:CS:A
CTIVE HIGH
:SERialbus<x>:SPI[:ANALyze]:SETup:CS
:SOURce
Function Sets or queries the chip select signal for SPI bus
signal analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:CS:
SOURce {<NRf>|BIT<x>|MATH<x>}
:SERialbus<x>:SPI[:ANALyze]:SETup:CS:
SOURce?
<x> = 1 to 4
<NRf> = 1 to 4
<x> of BIT<x> = 1 to 8
<x> of MATH<x> = 1 or 2
Example
:SERIALBUS1:SPI:ANALYZE:SETUP:CS:SOUR
CE 1
:SERIALBUS1:SPI:ANALYZE:SETUP:CS:SOUR
CE?
-> :SERIALBUS1:SPI:ANALYZE:SETUP:CS:S
OURCE 1
:SERialbus<x>:SPI[:ANALyze]:SETup:DA
TA<y>?
Function Queries all data signal settings for SPI bus signal
analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:DAT
A<y>?
<x> = 1 to 4
<y> = 1 or 2
:SERialbus<x>:SPI[:ANALyze]:SETup:DA
TA<y>:SOURce
Function Sets or queries the data signal for SPI bus signal
analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:DAT
A<y>:SOURce {<NRf>|BIT<x>|MATH<x>}
:SERialbus<x>:SPI[:ANALyze]:SETup:DAT
A<y>:SOURce?
<x> = 1 to 4
<y> = 1 or 2
<NRf> = 1 to 4
<x> of BIT<x> = 1 to 8
<x> of MATH<x> = 1 or 2
Example
:SERIALBUS1:SPI:ANALYZE:SETUP:DATA1:S
OURCE 1
:SERIALBUS1:SPI:ANALYZE:SETUP:DATA1:S
OURCE?
-> :SERIALBUS1:SPI:ANALYZE:SETUP:DATA
1:SOURCE 1
5.24 SERialbus Group