YOKOGAWA DLM2000 Series - Page 275

5-242
IM 710105-17E
:TRIGger{[:ATRigger]|:BTRigger}:FLEX
ray[:IDData]:CCOunt:COUNt<x>
Function Sets or queries the cycle count, which is one of
the ID and data conditions, for FLEXRAY bus
signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:CCOunt:COUNt<x> {<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:CCOunt:COUNt<x>?
<x> = 1 or 2
<NRf> = 0 to 63
Example
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:CCOU
NT:COUNT1 1
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:CCOU
NT:COUNT1?
-> :TRIGGER:ATRIGGER:FLEXRAY:IDDATA:C
COUNT:COUNT1 1
Description • For :TRIGger{[:ATRigger]|:BTRigger}:
FLEXray[:IDData]:CCOunt:CONDition
EQUal|GREater|NOTEqul, set the cycle-count
setting using :TRIGger{[:ATRigger]|:BTRigger}:
FLEXray[:IDData]:CCOunt:COUNt1.
• For :TRIGger{[:ATRigger]|:BTRigger}:FLEXray[:I
DData]:CCOunt:CONDition LESS, set the cycle-
count setting using :TRIGger{[:ATRigger]|:BTRi
gger}:FLEXray[:IDData]:CCOunt:COUNt2.
• For :TRIGger{[:ATRigger]|:BTRigger}:
FLEXray[:IDData]:CCOunt:CONDition
BETWeen|NOTBetween, set the smaller value
using :TRIGger{[:ATRigger]|:BTRigger}:FLEXra
y[:IDData]:CCOunt:COUNt1, and set the larger
value using :TRIGger{[:ATRigger]|:BTRigger}:F
LEXray[:IDData]:CCOunt:COUNt2.
:TRIGger{[:ATRigger]|:BTRigger}:FLEX
ray[:IDData]:CCOunt:MODE
Function Sets or queries the cycle-count enable/disable
condition, which is one of the ID and data
conditions, for FLEXRAY bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:CCOunt:MODE {<Boolean>}
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:CCOunt:MODE?
Example
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:CCOU
NT:MODE ON
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:CCOU
NT:MODE?
-> :TRIGGER:ATRIGGER:FLEXRAY:IDDATA:C
COUNT:MODE 1
:TRIGger{[:ATRigger]|:BTRigger}:FLEX
ray[:IDData]:DATA<x>?
Function Queries all data field settings for the ID and data
conditions for FLEXRAY bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:DATA<x>?
<x> = 1 or 2
:TRIGger{[:ATRigger]|:BTRigger}:FLEX
ray[:IDData]:DATA<x>:BCOunt
Function Sets or queries the position for comparing data
field data patterns, which is one of the ID and data
conditions, for FLEXRAY bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:DATA<x>:BCOunt {<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:DATA<x>:BCOunt?
<x> = 1 or 2
<NRf> = 0 to 253
Example
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:DATA
1:BCOUNT 1
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:DATA
1:BCOUNT?
-> :TRIGGER:ATRIGGER:FLEXRAY:IDDATA:D
ATA1:BCOUNT 1
:TRIGger{[:ATRigger]|:BTRigger}:FLEX
ray[:IDData]:DATA<x>:CONDition
Function Sets or queries the data field data condition, which
is one of the ID and data conditions, for FLEXRAY
bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:DATA<x>:CONDition {BETWee
n|EQUal|FALSe|GREater|LESS|NOTBetween
|NOTEqul|TRUE}
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:DATA<x>:CONDition?
<x> = 1 or 2
Example
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:DATA
1:CONDITION BETWEEN
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:DATA
1:CONDITION?
-> :TRIGGER:ATRIGGER:FLEXRAY:IDDATA:D
ATA1:CONDITION BETWEEN
:TRIGger{[:ATRigger]|:BTRigger}:FLEX
ray[:IDData]:DATA<x>:DBYTe
Function Sets or queries the number of data field data
bytes, which is one of the ID and data conditions,
for FLEXRAY bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:DATA<x>:DBYTe {<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:FLEXr
ay[:IDData]:DATA<x>:DBYTe?
<x> = 1 or 2
<NRf> = 1 to 8
Example
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:DATA
1:DBYTE 1
:TRIGGER:ATRIGGER:FLEXRAY:IDDATA:DATA
1:DBYTE?
-> :TRIGGER:ATRIGGER:FLEXRAY:IDDATA:D
ATA1:DBYTE 1
5.33 TRIGger Group