EasyManuals Logo

Zebra TC52 Integrator Guide

Zebra TC52
192 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #82 background imageLoading...
Page #82 background image
DataWedge
82
Code ID Type - A Code ID character identifies the code type of a scanned barcode. This is useful when the
reader is decoding more than one code type. Select a code ID character to insert between the prefix and
the decoded symbol.
Code ID Type None - No prefix (default)
Code ID Type AIM - Insert AIM Character prefix.
Code ID Type Symbol - Insert Symbol character prefix.
Engine Decode LED - Use to turn on scanner red LED when the scan beam is emitting either by scanner
trigger or using soft scan button.
BT Disconnect On Exit - Bluetooth connection is disconnected when data capture application is closed .
Connection Idle Time - Set connection idle time. The Bluetooth connection disconnects after being idle for
set time.
Display BT Address Barcode - Enable or disable displaying Bluetooth Address bar code if there is no
Bluetooth scanner being paired when application tries to enable the Bluetooth scanner.
Establish Connection Time - The timeout which the device will try to enable or reconnect to the Bluetooth
scanner when the Bluetooth scanner is not in the vicinity or not paired.
Audio Feedback Mode - Select good decode audio indication.
Local Audio Feedback - Good decode audio indication on device only.
Remote Audio Feedback - Good decode audio indication.
Both - Good decode audio indication on device and scanner (default).
Disable - No good decode audio indication on either device or scanner.
LED Feedback Mode - Select good decode LED indication.
Local LED Feedback - Good decode LED indication on device only.
Remote LED Feedback - Good decode LED indication on scanner.
Both - Good decode LED indication on device and scanner (default).
Disable - No good decode LED indication on either device or scanner.
Decode Audio Feedback - Select an audio tone to sound upon a good decode (default optimized-beep).
Decoding LED Notification - Enable the device to light the red Data Capture LED when data capture is in
progress. (default - disabled).
Decode Feedback LED Timer
- Set the amount of time (in milliseconds) that the green Data Capture LED
stays lit after a good decode. (default - 75 msec.)
Beep Volume Control - Set the good decode beep to a system or other sound. This allows for independent
control of the good beep volume.
NOTE: Not all ringtones are fully supported as decode tones and those of longer length may be truncated when used as a
decode tone. The recommendation is to test the selected tone for operation before deployment to a customer site.
Ringer - Set the good decode beep to the ringer sound.
Music and Media - Set the good decode beep to the media sound.
Alarms - Set the good decode beep to the alarm sound.
Notifications - Set the good decode beep to the notification sound (default).
UDI Params
Allows the configuration of parameters specific to healthcare barcodes.
Enable UDI-GSI - Enable UDI using GS1 standards (default - enabled).
Enable UDI-HIBCC - Enable UDI using HIBCC standards (default - enabled).

Table of Contents

Other manuals for Zebra TC52

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Zebra TC52 and is the answer not in the manual?

Zebra TC52 Specifications

General IconGeneral
RFID reader-
Scanner type2D
Product colorBlack
Phone functionYes
Display diagonal5 \
Touch technologyDual-touch
Touchscreen typeCapacitive
Display resolution1280 x 720 pixels
USB 2.0 ports quantity1
Flash memory32 GB
Internal memory4 GB
Compatible memory cardsMicroSD (TransFlash)
Maximum memory card size256 GB
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)-20 - 50 °C
Operating relative humidity (H-H)5 - 95 %
Battery capacity4150 mAh
Number of cores8
Processor model660
Processor familySnapdragon
Processor frequency2.2 GHz
Processor manufacturerQualcomm
GPS (satellite)No
Operating system installedAndroid
Bluetooth version5.0
Rear camera aperture number2.2
Front camera aperture number2
Rear camera resolution (numeric)13 MP
Front camera resolution (numeric)5 MP
Weight and Dimensions IconWeight and Dimensions
Depth18.6 mm
Width75.5 mm
Height155 mm
Weight249 g

Related product manuals