ABB A135-M65 - Tables

Operation Manual / 4 Product description / A130-M.. - A145-M..
Tables
Page 121 /
121
© Copyright 2017 ABB. All rights reserved.
HZTL4031_EN
Revision E
January 2017
Tables
Table 1
Related documents ...................
5
Table 2
Weights of turbochargers A130-
M.. – A145-M.. ...........................
11
Table 3
Requirements for threaded rods
17
Table 4
Tightening torques for standard
nuts ............................................
19
Table 5
Pressure screw tightening tor-
ques ...........................................
21
Table 6
Lubricating oil pressure, oil inlet
29
Table 7
Lubricating oil temperature at
the inlet ......................................
30
Table 8
Lubricating oil temperature at
the outlet ....................................
30
Table 9
Tightening torque (86505).........
34
Table 10
Expected replacement intervals
41
Table 11
Maintenance table .....................
45
Table 12
Parameters for wet cleaning of
compressor ...............................
49
Table 13
Turbine wet cleaning, recom-
mended operating state ............
52
Table 14
Wet cleaning of turbines, pa-
rameters ....................................
53
Table 15
Value table for soaking .............
61
Table 16
Malfunctions when starting –
Delayed start-up ........................
65
Table 17
Malfunctions when starting –
Vibrations ..................................
65
Table 18
Malfunctions when starting –
Rubbing of rotating parts ...........
65
Table 19
Malfunctions during operation –
Lubricating oil pressure too low
66
Table 20
Malfunctions during operation –
Speed reduces ..........................
66
Table 21
Malfunctions during operation –
Speed increases .......................
66
Table 22
Malfunctions during operation –
Exhaust gas temperature too
high ............................................
67
Table 23
Malfunctions during operation –
Charge air pressure too low ......
67
Table 24
Malfunctions during operation –
Charge air pressure too high ....
68
Table 25
Malfunctions during operation –
Engine performance losses .......
68
Table 26
Malfunction – Turbocharger
pumping .....................................
69
Table 27
Malfunction – Sporadic surge
blows ..........................................
69
Table 28
Malfunctions when stopping –
Runout noises ............................
70
Table 29
Malfunctions when stopping –
Runout time too short.................
70
Table 30
Malfunction of the speed meas-
urement system
– No signal or
poor signal amplitude .................
71
Table 31
Malfunction of the speed meas-
urement system
– Measured
speed too high ...........................
71
Table 32
Malfunction of the speed meas-
urement system
– Measured
speed too low .............................
71
Table 33
Swivel lifting eyes .......................
75
Table 34
Ring nuts to be used ..................
76
Table 35
Weights of assemblies ...............
77
Table 36
3 press-off screws ......................
82
Table 37
6 press-off screws ......................
83
Table 38
Permissible clearances A and B
91
Table 39
Permitted nozzle ring compres-
sion PD .......................................
92
Table 40
Tightening torque (51007) .........
95
Table 41
Tightening torque (79041) .........
97
Table 42
Tightening torque (72011) .........
98
Table 43
Permissible clearances N and
R .................................................
99
Table 44
Tightening torque (72020) .........
100
Table 45
Tightening torque (51009) .........
103
Table 46
Tightening torques .....................
105
Table 47
Tightening torques for insulation
106
Table 48
Cover plate dimensions [mm] ....
110
Table 49
Customer spare part set 97070 .
115
Table 50
Spare parts list ...........................
117