ABB HT611036 - Page 197

Operation Manual / A150-M56/66/57/67 - A155-M..
Figures
© Copyright 2022 ABB. All rights reserved. HZTL4032_EN Revision S February 2022
Fig.61: Removing cartridge group 1........................ 111
Fig.62: Removing cartridge group 2 ....................... 112
Fig.63: Removing cartridge group 3 ....................... 113
Fig.64: Installing the cartridge group on the service
support.......................................................................... 114
Fig.65: Removing the nozzle ring ............................ 115
Fig.66: Measuring clearance A and B...................... 116
Fig.67: Nozzle ring compression PD ....................... 117
Fig.68: Installing the nozzle ring ............................. 118
Fig.69: Lifting the cartridge group and rotating it
by 90°............................................................................. 119
Fig.70: Turning the cartridge group ...................... 120
Fig.71: Installing the cartridge group ..................... 121
Fig.72: Fitting the wall insert and the diffuser ..... 122
Fig.73: Installing the compressor casing............... 123
Fig.74: Turning the cartridge group with com-
pressor and turbine casing ....................................... 124
Fig.75: Installing the gas outlet flange................... 125
Fig.76: Measuring clearances N and R.................... 126
Fig.77: Fitting the insulation .................................... 127
Fig.78: Installing the cartridge group with com-
pressor and turbine casing ....................................... 128
Fig.79: Installing the cartridge group with com-
pressor and turbine casing ....................................... 128
Fig.80: Fitting gas outlet casing without support .....
129
Fig.81: Installing gas outlet casing with support 1.....
130
Fig.82: Installing gas outlet casing with support 2 ....
131
Fig.83: Installing the air inlets.................................. 132
Fig.84: Installing the uncoupled filter silencer ..... 133
Fig.85: Removing the air inlets ................................ 134
Fig.86: Removing the uncoupled filter silencer.... 135
Fig.87: Removing the compressor casing ............. 136
Fig.88: Pressing off compressor casing ................ 137
Fig.89: Remove the diffuser ..................................... 137
Fig.90: Dismantling the diffuser and the wall insert..
138
Fig.91: Removing insulation sheets ........................ 139
Fig.92: Removing cartridge group1........................ 139
Fig.93: Removing cartridge group 2 ....................... 140
Fig.94: Removing cartridge group 2 ........................ 141
Fig.95: S_05180 ........................................................... 142
Fig.96: Measuring clearance A and B ...................... 143
Fig.97: Nozzle ring compression PD........................ 144
Fig.98: Installing the nozzle ring.............................. 145
Fig.99: Installing the cartridge group 1.................. 146
Fig.100: Installing the cartridge group 2................ 147
Fig.101: Fitting the wall insert and the diffuser.... 148
Fig.102: Installing the compressor casing............. 149
Fig.103: Measuring clearances N and R .................. 150
Fig.104: Fitting the insulation................................... 151
Fig.105: Installing the air inlets................................ 152
Fig.106: Installing the uncoupled filter silencer.... 153
Fig.107: Customer tool .............................................. 154
Fig.108: Customer tool .............................................. 154
Fig.109: Positioning the collection tub................... 155
Fig.110: Removing the fastening strips.................. 155
Fig.111: Fitting the upper fastening strips ............ 156
Fig.112: Fitting the bottom fastening strip........... 156
Fig.113: Fitting the bottom fastening strip........... 157
Fig.114: Fitting the cartridge group........................ 158
Fig.115: Positioning the fastening strip ................. 159
Fig.116: Clamping piece............................................. 160
Fig.117: Attach nut ....................................................... 161
Fig.118: Initial situation ............................................. 162
Fig.119: Disassembly of the elbows ........................ 162
Fig.120: Disassembly of the elbows........................ 163
Fig.121: Pipe disassembly.......................................... 163
Fig.122: Disassembly of the connecting pieces.... 164
Fig.123: Disassembly of the cleaning nozzle ......... 164
Fig.124: Assembly of the cleaning nozzle............... 165
Fig.125: Assembly of the connecting pieces ......... 165
Page 195 / 198Page 195 / 198