ABB HT611036 - Page 199

Operation Manual / A150-M56/66/57/67 - A155-M..
Tables
© Copyright 2022 ABB. All rights reserved. HZTL4032_EN Revision S February 2022
Tables
Table1: Definition of pictograms ............................... 9
Table2: Personal protective equipment to be worn
at all times ...................................................................... 14
Table3: Personal protective equipment to be worn
specific to the respective task ................................... 14
Table4: Weight of complete turbocharger unit .... 29
Table5: Fitting the turbocharger, value X, L........... 36
Table6: Torque-controlled tightening of the pres-
sure screws ................................................................... 38
Table7: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 45
Table8: Lubricating oil temperature at the inlet... 46
Table9: Maximum lubricating oil temperature at the
outlet .............................................................................. 46
Table10: Tightening torque(86505)........................ 50
Table11: Expected replacement intervals ............... 56
Table12: Maintenance table....................................... 59
Table13: Parameters for wet cleaning of com-
pressor ........................................................................... 62
Table14: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 65
Table15: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 66
Table16: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 67
Table17: Tightening torque(81272) .......................... 72
Table18: Tightening torque(81273).......................... 72
Table19: Value table for soaking ............................... 77
Table20: Tightening torque (81152 / 81154) ........... 81
Table21: Malfunctions when starting – Delayed
start-up .......................................................................... 82
Table22: Malfunctions when starting – Vibrations 82
Table23: Malfunctions when starting – Rubbing of
rotating parts................................................................ 82
Table24: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 83
Table25: Malfunctions during operation – Speed re-
duces............................................................................... 83
Table26: Malfunctions during operation – Speed in-
creases............................................................................. 83
Table27: Malfunctions during operation – Exhaust
gas temperature too high............................................ 84
Table28: Malfunctions during operation – Charge air
pressure too low............................................................ 84
Table29: Malfunctions during operation – Charge air
pressure too high .......................................................... 85
Table30: Malfunctions during operation – Engine
performance losses....................................................... 85
Table31: Malfunction – Turbocharger surging........ 86
Table32: Malfunction – Sporadic surge blows ........ 86
Table33: Malfunctions when stopping – Runout
noises............................................................................... 87
Table34: Malfunctions when stopping – Runout
time too short ................................................................ 87
Table35: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 88
Table36: Malfunction of the speed measurement
system – Measured speed too high........................... 88
Table37: Malfunction of the speed measurement
system – Measured speed too low............................. 88
Table38: Swivel lifting eyes......................................... 90
Table39: Press-off screws........................................... 91
Table40: Dismantling screw....................................... 91
Table41: Weights of assemblies ................................ 96
Table42: Tightening torques...................................... 97
Table43: Tightening torques for insulation ............ 98
Table44: 3 press-off screws ..................................... 105
Table45: 6 press-off screws ..................................... 106
Table46: Tightening torque (90012-01) .................. 111
Table47: Permissible clearances A and B ................ 116
Table48: Nozzle ring compression PD..................... 117
Table49: Tightening torque (90012-01) ................. 120
Table50: Tightening torque (51007) ........................ 121
Table51: Tightening torque (79041)........................ 122
Table52: Tightening torque (72011) ....................... 123
Table53: Permissible clearances N and R............... 126
Page 197 / 198Page 197 / 198