ABB XAC18513 - Figures

Operation Manual / 4 Product description / A100-L
Figures
© Copyright 2017 ABB. All rights reserved. HZTL4034_EN Revision K June 2017
Figures
Fig.1: Layout and function of the turbocharger...... 4
Fig.2: Warning plate locations .................................... 6
Fig.3: Locations of the rating plates .......................... 7
Fig.4: Fitting lifting gear to turbocharger................ 9
Fig.5: Placing the turbocharger on the bracket ..... 10
Fig.6: Compressor-end foot....................................... 11
Fig.7: Turbine-end foot................................................ 11
Fig.8: Layout and overview of the speed measure-
ment system................................................................... 18
Fig.9: Replacing the speed sensor ........................... 20
Fig.10: U-tube manometer at the filter silencer..... 22
Fig.11: Noise insulation, bellows............................... 24
Fig.12: Layout and overview of filter silencer ......... 32
Fig.13: Dismantling filter ring circumferential part....
34
Fig.14: Opening filter ring lock.................................. 34
Fig.15: Attaching new filter ring ............................... 35
Fig.16: Fitting new filter ring..................................... 35
Fig.17: Overview of wet cleaning of compressor .. 38
Fig.18: Filter plug view................................................ 39
Fig.19: Overview of dry cleaning device ................... 41
Fig.20: Drain pipe diagram ........................................ 44
Fig.21: Overview of assembly weights .................... 53
Fig.22: Overview of filter silencer casing disas-
sembly and assembly .................................................. 54
Fig.23: Fitting filter silencer casing 1....................... 55
Fig.24: Fitting filter silencer casing 2 ...................... 56
Fig.25: Fitting filter silencer casing 3 ...................... 56
Fig.26: Fitting filter silencer casing 4....................... 57
Fig.27: Fitting filter silencer casing 5 ....................... 57
Fig.28: Fitting the bellows ......................................... 58
Fig.29: Dismantling the filter silencer ..................... 59
Fig.30: Dismantling the filter silencer ..................... 60
Fig.31: Dismantling the filter silencer with noise
package ........................................................................... 61
Fig.32: Pressing off compressor casing................... 62
Fig.33: Moving out wall insert .................................... 63
Fig.34: Putting down wall insert ................................ 63
Fig.35: Putting down wall insert ................................ 64
Fig.36: Dismantling the diffuser ............................... 65
Fig.37: Measuring axial clearance A........................... 66
Fig.38: Removing the insulation (A175-L and smal-
ler)..................................................................................... 67
Fig.39: Dismantling the gas inlet casing (A175-L and
smaller) ............................................................................ 68
Fig.40: Dismantling the nozzle ring (A175-L and
smaller) ............................................................................ 68
Fig.41: Dismantling the gas inlet casing (A180-L and
larger)............................................................................... 69
Fig.42: Fitting the nozzle ring holder........................ 70
Fig.43: Dismantling the nozzle ring (A180-L and lar-
ger) .................................................................................... 71
Fig.44: Putting down the nozzle ring (A180-L and
larger)................................................................................ 71
Fig.45: Fitting the nozzle ring (A175-L and smaller) ...
72
Fig.46: Fitting the gas outlet casing (A175-L and
smaller) ............................................................................ 73
Fig.47: Fit insulation..................................................... 74
Fig.48: Looping around the nozzle ring (A180-L and
larger)............................................................................... 75
Fig.49: Fitting the nozzle ring (2) (A180-L and larger)
76
Fig.50: Fitting the gas inlet casing (A180-L and lar-
ger) ................................................................................... 77
Fig.51: Measuring axial clearance A........................... 78
Fig.52: Fitting the diffuser.......................................... 79
Fig.53: Positioning wall insert .................................... 80
Fig.54: Fitting the wall insert .................................... 81
Fig.55: Fitting the filter silencer ................................ 82
Fig.56: Fitting the filter silencer ................................ 83
Fig.57: Fitting the filter silencer with noise package .
84
Page 104 / 106Page 104 / 106