Home
Agilent Technologies
Test Equipment
54853A
Agilent Technologies 54853A User Manual
4
of 1
of 1 rating
194 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Chapter 6: Replacing
Assemblies
To rem
ove an
d re
plac
e the CD
-RO
M driv
e
6–30
8
Remove the CD-ROM Adapt
er Board from t
he rear of t
he CD-ROM drive.
9
To replace
the CD-ROM drive, r
everse the a
bove proced
ure with a new dri
ve.
163
165
Table of Contents
Default Chapter
5
In this Book
5
Table of Contents
7
1 General Information
11
Instruments Covered by this Service Guide
12
Accessories Supplied
13
Options Available
13
Accessories Available
13
Specifications and Characteristics
15
Dimensions
21
Recommended Test Equipment
22
2 Setting up the Oscilloscope
26
To Connect Power
27
To Connect the Mouse or Other Pointing Device
29
To Connect the Keyboard
30
To Connect to the LAN Card
31
To Connect Oscilloscope Probes
32
To Connect SMA Cables
34
To Connect a Printer
35
To Connect an External Monitor
37
To Connect a GPIB Cable
37
To Tilt the Oscilloscope Upward for Easier Viewing
39
To Turn on the Oscilloscope
40
To Turn off the Oscilloscope
40
To Verify Basic Oscilloscope Operation
41
Installing Application Programs on Infiniium
42
Changing Windows System Settings
42
To Clean the Oscilloscope
43
3 Testing Performance
45
Performance Test Interval
46
Performance Test Record
46
Test Order
46
Test Equipment
46
Before Performing Performance Verification Testing
47
Vertical Performance Verification
48
Offset Performance Test
49
DC Measurement Accuracy (Single Cursor) Test
55
Analog Bandwidth - Maximum Frequency Check
60
Horizontal Performance Verification
67
Time Base Accuracy Test
68
Delta-Time Measurement Accuracy Test
72
Trigger Performance Verification
75
Internal Channel Trigger Sensitivity Test
76
Trigger Jitter Test
87
Agilent 54853A/54A/55A Performance Test Record
91
4 Calibration
95
Equipment Required
96
Self Calibration Interval and Hardware Adjustments
96
Mainframe Cal Factor Memory Error
96
Operating Hints
97
Loading Default Oscilloscope Settings
97
Loading New Software
97
Calibration Procedures
97
To Check the Flat Panel Display (FPD)
98
To Run the Self Calibration
101
5 Troubleshooting
103
Safety
104
Tools Required
104
ESD Precautions
104
Keystroke Conventions
104
Default Setup
105
To Install the Fan Safety Shield
105
To Troubleshoot the Instrument
106
Primary Trouble Isolation
108
No Display Trouble Isolation
112
Front Panel Display Debug
113
Motherboard Verification
115
To Configure the Motherboard Jumpers and Setup BIOS
118
POST Code Listing
121
Front Panel Debug
123
Power Supply Trouble Isolation
124
Power Board Trouble Isolation
126
Autoprobe Board Trouble Isolation
127
To Check the Keyboard; Troubleshooting Procedure
128
To Check the Leds
129
To Troubleshoot the Acquisition System
130
Software Revisions
131
To Check Probe Power Outputs
132
To Check the SVGA Display Board Video Signals
133
To Check the Backlight Inverter Voltages
134
6 Replacing Assemblies
135
ESD Precautions
136
Tools Required
136
To Return the Oscilloscope to Agilent Technologies for Service
137
To Remove and Replace the Covers
138
To Disconnect and Connect Mylar Flex Cables
140
To Remove and Replace the Autoprobe Assembly
141
To Remove and Replace the Probe Power and Control Board
143
To Remove and Replace the Backlight Inverter Board
145
To Remove and Replace the Front Panel Assembly
147
To Remove and Replace the Keyboard and Flat-Panel Display Assemblies
150
To Remove and Replace the Acquisition Board Assembly
153
To Remove and Replace the Power Regulator Distribution Board
156
To Remove and Replace the GPIB Interface Board
157
To Remove and Replace the PCI Bridge Board
158
To Remove and Replace the Scope Interface Board and SVGA Display Board
159
To Remove and Replace the Floppy Disk Drive
160
To Remove and Replace the Internal Hard Disk Drive
161
To Remove and Replace the CD-ROM Drive
163
To Remove and Replace the Motherboard
165
To Remove and Replace the Motherboard
166
To Remove and Replace the Power Supply
167
To Remove and Replace the Fans
171
7 Replaceable Parts
173
Ordering Replaceable Parts
174
Power Cables and Plug Configurations
175
Exploded Views
177
Replaceable Parts List
182
8 Theory of Operation
187
Block-Level Theory
189
Acquisition Theory
191
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Agilent Technologies 54853A and is the answer not in the manual?
Ask a question
Agilent Technologies 54853A Specifications
General
Brand
Agilent Technologies
Model
54853A
Category
Test Equipment
Language
English
Related product manuals
Agilent Technologies 54810A
132 pages
Agilent Technologies 54835A
208 pages
Agilent Technologies 54831A
133 pages
54830 Series
133 pages
Agilent Technologies 54621A
276 pages
Agilent Technologies 54624A
276 pages
Agilent Technologies 54622D
276 pages
Agilent Technologies 54641A
276 pages
Agilent Technologies 54622A
276 pages
Agilent Technologies 5530
378 pages
Agilent Technologies 5000 Series
126 pages
Medalist i3070 5i Series
181 pages
Need help?
General
To Next Page