Home
Agilent Technologies
Laboratory Equipment
6490
Agilent Technologies 6490 Installation Guide
5
of 1
of 1 rating
112 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
48
Agilent 6400 Series Triple Quad LC/MS System Installation Guide
This page intent
ionally left blank.
47
49
Table of Contents
Default Chapter
5
Table of Contents
5
1 Instrument Installation
7
Step 1. Unpack and Set up the Triple Quadrupole LC/MS
9
Step 2. Prepare to Install the System
10
Step 3. Set up the Agilent MS40+ Pumps
14
Step 4. Connect the Triple Quadrupole LC/MS
18
Step 5. Install the Spray Chamber
27
Step 6. Install the Agilent LC System
34
2 Software Installation and Configuration
35
Step 1. Set up the Computer System
36
Step 2. Check PC Network Card Configuration
37
Step 3. Prepare for Installation
38
Step 4. Install the Data Acquisition Program
39
Step 5. Install the Qualitative Analysis Program
40
Step 6. Install the Quantitative Analysis Program
41
Step 7. Install Microsoft Excel (Optional)
41
Step 8. Install Service Packs for Data Acquisition
41
Step 9. Install Quantitative Analysis Reporting
42
Step 10. Configure Excel for Masshunter (Optional)
42
Step 11. Configure the Instrument
42
Step 12. Copy the Support Folder to the Computer
44
Step 13. Confirm the LC Firmware Revision
46
Step 14. Finish the Installation
47
3 Installation Completion and System Verification
49
Step 1. Condition the Agilent LC Instrument
50
Step 2. Reset the Collision Cell Gas Flow Rate
54
Step 3. Prepare the Performance Evaluation Samples
58
Step 4. Set up Methods and Worklists
60
Step 5. Verify the Triple Quadrupole LC/MS Sensitivity
63
4 Installation and Verification of Other Sources
73
G1947B APCI Source
74
To Install the G1947B APCI Source
74
To Verify the Operation of the G1947B APCI Source
75
G1978B Multimode Source
76
To Install the G1978B Multimode Source
76
To Verify the Operation of the G1978B Multimode Source
78
G1971B APPI Source
79
To Install the G1971B APPI Source
79
To Verify the Operation of the G1971B APPI Source
81
5 Other Setup Tasks
83
To Start the Data Acquisition Program
84
To Stop Masshunter Engines
84
To Stop Masshunter Processes in Case of Unrecoverable Errors
85
To View the Log Book
85
To Configure Log Book Notification
86
To Configure the Network Interface Card
87
To Remove the Masshunter Workstation Software
88
To Reconfigure the Instrument
89
To Confirm the Collision Cell Gas Flow Rate (6470A and 6495A/B Only)
91
6 Reference
105
Positive Ion Mode Checkout Conditions
106
Negative Ion Mode Checkout Conditions
109
Other manuals for Agilent Technologies 6490
Quick Start Guide
28 pages
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Agilent Technologies 6490 and is the answer not in the manual?
Ask a question
Agilent Technologies 6490 Specifications
General
Brand
Agilent Technologies
Model
6490
Category
Laboratory Equipment
Language
English
Related product manuals
Agilent Technologies 6495
28 pages
Agilent Technologies 6460
28 pages
Agilent Technologies 6475
90 pages
Agilent Technologies 6430
72 pages
Agilent Technologies 6420
72 pages
Agilent Technologies 6400 Series
28 pages
Agilent Technologies 6890N
102 pages
Agilent Technologies 6890 Plus
867 pages
Agilent Technologies 6500 Series
154 pages
Agilent Technologies 6890 Series
286 pages
Cary 630 FTIR
72 pages
6850 Series II
256 pages
Need help?
General
To Next Page
