Agilent Technologies, Inc.
2850 Centerville Road
Wilmington, DE 19808-1610
Agilent Technologies
1997–2001
All Rights Reserved.
Reproduction, adaptation, or
translation without permission
is prohibited, except as allowed
under the copyright laws.
Part No. G2612-90107
Replaces Part No. G2612-90100
Second edition, May 2001
First edition, Jan 2000
Printed in USA
HP® is a registered trademark
of Hewlett Packard Co.
Microsoft®, Windows®, and
Windows NT® are registered
trademarks of Microsoft Corp.
Safety Information
The 7683 Automatic Liquid
Sampler meets the following
IEC (International
Electrotechnical Commission)
classifications: Safety Class 1,
Transient Overvoltage Category
II, and Pollution Degree 2. This
unit has been designed and
tested in accordance with
recognized safety standards and
designed for use indoors.
Whenever the safety protection
of the 7683 Automatic Liquid
Sampler has been
compromised, disconnect the
unit from all power sources and
secure the unit against
unintended operation.
The recyclable carbon
monoflouride lithium battery is
BR-2/3 A 1,200 mAh. Fuses F001
and F002 are 3 A, 250 Vac, IEC
127 Type T. Fuses F201 and
F202 are 10 A, 250 Vac, IEC 127
Type T. Fuse F101 is a 0.5 A,
250 Vac.
Warnings in this manual or on
the instrument must be
observed during all phases of
operation, service, and repair of
this instrument. Failure to
comply with these precautions
violates safety standards of
design and the intended use of
the instrument. Agilent
Technologies assumes no
liability for the customer’s
failure to comply with these
requirements.
Refer servicing to qualified
service personnel. Substituting
parts or performing any
unauthorized modification to
the instrument may result in a
safety hazard. Disconnect the
AC power cord before removing
covers. The customer should
not attempt to replace the
battery or fuses in this
instrument.
Safety Symbols
This manual contains safety
information that should be
followed by the user to ensure
safe operation.
WARNING
A warning calls attention to a
condition or possible situation
that could cause injury to the
user.
CAUTION
A caution calls attention to a
condition or possible situation
that could damage or destroy
the product or the user's work.
Electromagnetic
Compatibility
This device complies with the
requirements of CISPR 11.
Operation is subject to the
following two conditions:
1 This device may not cause
harmful interference.
2 This device must accept any
interference received,
including interference that
may cause undesired
operation.
If this equipment does cause
harmful interference to radio or
television reception, which can
be determined by turning the
equipment off and on, the user
is encouraged to try one or
more of the following measures:
1 Relocate the radio or
antenna.
2 Move the device away from
the radio or television.
3 Plug the device into a
different electrical outlet, so
that the device and the radio
or television are on separate
electrical circuits.
4 Make sure that all peripheral
devices are also certified.
5 Make sure that appropriate
cables are used to connect
the device to peripheral
equipment.
6 Consult your equipment
dealer, Agilent Technologies,
or an experienced technician
for assistance.
7 Changes or modifications not
expressly approved by
Agilent Technologies could
void the user’s authority to
operate the equipment.
Sound Emission Certi-
fication for Federal
Republic of Germany
Sound Pressure
Sound pressure Lp < 57 dB(A)
according to DIN-EN 27779.
When operating the Agilent
Automatic Liquid Sampler, the
sound pressure is
approximately 68 dB(A) during
short burst injection pulses.
Schalldruckpegel
Schalldruckpegel LP < 57 dB(A)
nach DIN-EN 27779.
Bei Betrieb des Agilent
automatischen Probendebers
treten beim Oeffnen des Ventils
kurzfristig Impulse bis su einem
Schalldruckpegel Lp von ca.
68 dB(A) auf.
To Next Page
Loading...
Need help?
General
