Index
Service Guide N5230-90014 Index-3
troubleshooting, 4-28
typical power output
, 4-43
B trace
troubleshooting, 4-28, 4-30
B1 fan
removal and replacement, 7-40
band modes
troubleshooting
all bands, 4-40, 4-41
band 4
, 4-38, 4-40
bands 0-3
, 4-38, 4-40
bands 5–12, 4-38, 4-41
battery
removal and replacement
illustrated
, 7-44
procedure, 7-43
battery disposal
, 1-8
before applying power
, 1-3
block diagram
configurable test set,
Option 014
, 5-17
digital control group, 5-22
digital processor group
, 5-22
receiver group
, 5-20
signal separation group, active,
5-17
signal separation group,
passive
, 5-15
source group
, 5-7
bottom assembly, active
replaceable parts
illustrated, 6-19
part numbers
, 6-18, 6-20
bottom assembly, all options
hardware
illustrated, 6-25
part numbers
, 6-24
bottom assembly, passive
replaceable parts
illustrated
, 6-15
part numbers
, 6-14, 6-16
bracket
attenuator
illustrated
, 6-25
part number
, 6-24
broadband failure
, 4-36
built-in tests
for commercial calibration,
Option 897
, 2-4
for standards compliant
calibration, Option 898
, 2-5
C
cable
substitution, 3-23
test port
checks
, 3-10, 3-12, 3-13, 3-14,
3-15, 3-17
connector repeatability
failure
, 3-18
insertion loss failure, 3-14
magnitude and phase stability
failure
, 3-16
return loss failure, 3-13
cables
GPIB
part numbers
, 6-34
required for servicing, 2-8
cables, flexible
in top assembly, all options
illustrated
, 6-13
part numbers
, 6-12
cables, ribbon
in top assembly, all options
illustrated
, 6-13
part numbers, 6-12
cables, semi-rigid
in top assembly, all options
illustrated
, 6-13
part numbers, 6-12
cables, wrapped-wire
in top assembly, all options
illustrated
, 6-13
part numbers, 6-12
calibration
certificate of, 3-7
coefficients test
, 3-33
commercial, built-in tests,
Option 897
, 2-4
commercial, Option R-50C-001
,
2-10
kits
, 2-8, 3-7
substitution
, 3-23
measurement, 8-4
options available
, 2-10
receiver
, 3-38
source
, 3-37
standards compliant, built-in
tests, Option 898
, 2-5
standards compliant,
Option R-50C-002
, 2-10
care of connectors
, 3-5
caution
, 1-3
CD-RW drive
, 2-6
CE mark
, 1-7
certificate of calibration
, 3-7
changing
a serial number, 8-17
channel A
troubleshooting, 4-28, 4-42
typical power output
, 4-42
channel B
troubleshooting, 4-28, 4-42
typical power output, 4-43
channel R1
troubleshooting, 4-28
channel R2
troubleshooting, 4-28
checks
cable
connector repeatability, failure
of
, 3-18
insertion loss, failure of
, 3-14
magnitude and phase stability,
failure of
, 3-16
return loss, failure of
, 3-13
test port cables, 3-10, 3-12
operator’s
, 3-10
accessories used in
, 3-10
dialog box
, 3-11
failure of
, 3-11
performing
, 3-10
Port 1, 3-10
Port 2
, 3-10
preliminary
, 3-10
system, 3-1
getting ready
, 3-4
test port cable
accessories used in
, 3-12
connector repeatability
, 3-17
insertion loss
, 3-14
magnitude and phase
stability
, 3-15
performing
, 3-12
return loss, 3-13
COM
, 8-9
commercial calibration
built-in tests, Option 897, 2-4
commercial calibration,
Option R-50C-001
, 2-10
compression test, receiver
, 3-31
configurable test set, Option 014
,
2-3
block diagram, 5-17
operation, 5-16
configuration
high dynamic range
active measurement
, 5-18
diagram
, 5-18
normal
active measurement
, 5-17
Option 014
, 5-17
connector
care
principles of
, 3-5
quick reference
, 3-5
protective end caps
part numbers
, 6-34
repeatability check
failure of
, 3-18
of test port cables
, 3-17
connector repeatability
check
test port cables
, 3-17
connectors
care of, 3-5
To Next Page
Loading...
Need help?
General
