Index-2 Service Guide N5230-90014
Index
illustrated, 7-17
test nodes
, 4-33
troubleshooting
band 4
, 4-38
bands 0-3
, 4-38
bands 5–12, 4-38
A8 multiplier board
illustrated, 6-11
operation
, 5-9
part number, 6-10
removal and replacement
, 7-16
illustrated
, 7-17
test nodes
, 4-32
troubleshooting
all bands
, 4-41
A9 fractional-N synthesizer board
illustrated, 6-11
operation
, 5-9
part number
, 6-10
removal and replacement, 7-16
illustrated
, 7-17
test nodes
, 4-33
troubleshooting
band 4
, 4-40
bands 0-3
, 4-40
bands 5–12, 4-41
accessories
analyzer, 2-6
CD-RW drive
, 2-6
in operator’s check, 3-10
in test port cable checks
, 3-12
USB
part numbers
, 6-35
USB hub
, 2-6
accuracy
dynamic accuracy test, 3-34
frequency test, 3-30
adapters
required for servicing, 2-8
adding
options, 8-15
adjustments
frequency
at 10 MHz
, 3-35
LO power
, 3-36
receiver calibration
, 3-38
source calibration
, 3-37
system
, 3-1, 3-35
getting ready
, 3-4
administrator password
Agilent, 7-38
Agilent
administrator password, 7-38
contacting, 2-11
support
, 2-10
all traces
troubleshooting, 4-29
analyzer
accessories, 2-6
block diagram
digital control group
, 5-22
digital processor group
, 5-22
receiver group
, 5-20
signal separation group,
active
, 5-17
signal separation group,
passive
, 5-15
source group
, 5-7
covers
illustrated
, 6-29
part numbers
, 6-28
removal and replacement
, 7-6
display lamp
replacement illustrated
, 7-13
replacement procedure
, 7-12
external replaceable parts
illustrated
, 6-29
part numbers
, 6-28
feet
illustrated
, 6-29
part numbers
, 6-28
frequency range and max ouput
power
, 5-4
frequency reference board
assembly
, 5-10
front panel interconnects
, 5-23
functional groups
, 5-3
digital control, 5-5
digital processing
, 5-5
power supply
, 5-5
receiver group, 5-5
signal separation
, 5-4
synthesized source
, 5-4
internal replaceable parts
illustrated
, 6-27
part numbers
, 6-26
miscellaneous replaceable parts
part numbers
, 6-34
mounting in equipment rack
,
2-4
operation
configurable test set,
Option 014
, 5-16
CPU board
, 5-24
data acquisition subgroup
,
5-24
digital control group
, 5-21
digital processor group
, 5-21
display assembly
, 5-23
floppy disk drive
, 5-25
fractional-N synthesizer
boards
, 5-9
front panel interface board
,
5-23
front panel subgroup, 5-23
hard disk drive
, 5-25
keypad assembly
, 5-23
main RAM, 5-24
mixer brick
, 5-19
multiplier boards
, 5-9
processing subgroup, 5-24
receiver group
, 5-19
signal separation group
, 5-15
source group, 5-6
source step attenuators
, 5-16
SPAM board–analog
, 5-19
SPAM board–digital, 5-24
SSLAM
, 5-9, 5-16
test port couplers
, 5-16
test set motherboard
, 5-11
USB hub
, 5-25
options
, 2-3
rear panel
interconnects
, 5-10, 5-11, 5-25
rear panel replaceable parts
illustrated
, 6-31
part numbers
, 6-30
strap handle
illustrated
, 6-29
part number
, 6-28
system block diagram
, 5-3
system operation
theory of
, 5-3
upgrades
, 2-6
warmup time, 3-4
ANSI/NCSL Z540-1-1994
verification, 3-8
ANSI/NCSL Z540–1–1994
non-type verification, 3-9
assemblies
location of part numbers, 6-7
rebuilt-exchange
procedure
, 6-5
rebuilt-exchange program
, 6-5
replacement
cautions about
, 7-4
list of procedures
, 7-5
sequence
, 6-4, 7-4
warnings about
, 7-4
attenuator bracket
illustrated, 6-25
part number
, 6-24
attenuators
required for servicing, 2-8
source
operation
, 5-16
AUX I/O connector
pin assignments, 5-14
rear panel, 5-11
B
B channel
To Next Page
Loading...
Need help?
General
